Jump to content
SAU Community

Is It Safe To Use 4 Car Stands At Once

made_guy

By made_guy,
in General Maintenance

 Share

Recommended Posts

gtrchick Community Regular

gtrchick

Posted
Posted

Ive never ever had a problem jacking up a vehicle from the diff, theres nothing wrong with it. Some vehicles dont have a jacking point, so your only choice is to use the diff.

Sills are where you put the stands, because thats what they were made for, when you see a car being put on a 2 poster hoist, unless its a 4wd/ute and some vans, the 4 pads usually go under the sills.

I think aslong as you have safely rested the car on the stands, whether it be 2 or 4, and always do the shake test, i mean id rather see my car fall with me shaking it then fall with me under it. Ive never ever seen stands failim not saying they dont though.... and ive been using them regularly for a while. I guess it also depends on quality, its no use in being a cheap skate and getting some el cheapo deal, always go for what tradies use.

And i figure if you are too scared to get under a car, then just dont you start getting paranoid at the slightest creak or groan, i used to be terrified, thinking how the hell is that little puny jack going to hold up 2 tonnes of car.... but i got over it, you jsut have to place trust in the equipment you are using, and if not, just get someone else to work on your car.

but thats just my 2cents

Bl4cK32 Grand Master

Bl4cK32

Posted
Posted

If i need to work under a car i will always use 2 drive on ramps at the front and 2 stands at the rear.

However, if i need to work on the front that requires the tyres coming off, then i will use 2 stands on the front only, and not jack up the rear. Once finished on the front then i will use ramps to get under the car.

cowie165 Veteran

cowie165

Posted
Posted
If i need to work under a car i will always use 2 drive on ramps at the front and 2 stands at the rear.

That'd be my preference too but my wheels are 9.5" wide! You have to buy 4x4 size ramps and they cost uber $$$. :) So jack stands it is for me then!

Godzilla32 Veteran

Godzilla32

Posted
Posted

During my restoration i have had my car on 4 stands the whole time. Thats about 1 year on them so far. Its the proper way to lift the car when you have no hoist and a regular practise in the workshop where a hoist is not available. If setup correctly it is completely safe!

Deren

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • joshuaho96
      Cas issue

      By joshuaho96 · Posted

      Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • joshuaho96
      Jacks that fit under GTR lips that can reach the subframe?

      By joshuaho96 · Posted

      On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      Nice....looking forward to that update
×
×
  • Create New...