Jump to content
SAU Community

Recommended Posts

Hey I've got a series 2 r33.

It's pretty much stock except for splitfire coilpacks and a heavy duty clutch.

I'm getting a turbo back highflow exhaust in the next week or two and am going to get a turbosmart boost controller at the same time and up it to 10psi.

The issue:

For these mods, is it worth getting a justjap cooler for a few hundred more than an r34 smic, or is an r34 smic all that is needed?

Can more boost be run (say 12psi) be run safely through an r34 smic as compared to the r33 smic?

With 12psi is in unrealistic to aim for a mid 14??

Also, does wrapping the dump and front pipe of the exhaust in heat wrap make much of a difference? Is it worth doing?

Thanks to whoever helps me out.

Steve.

I got full exhaust- 14.0 secs flat..

other mods: pod filter.. thats not really a performance mod.. n thats basically it.. 14 flat.. With 18inch rims front, 17inch rears.. lol

Anyways, the 34 cooler will be enough for around 200-210kw..

I wouldnt go past 0.8 bar, till you get your car tuned!!

if you are on a tight budget, add an SAFC in there and get it tuned.

SAFC with the blue screen is worth about $300 or so. Tune is about $150.

install it yourself..

it only has like 6 wires.

comes with instructions.

and you can search and find the ECU pin out diagram for your car on here somewhere..

that way, with your r34 cooler, exhaust, and extra boost, you can have the fueling tuned to make sure it's safe and also gain more power at the same time..

yes.

heat wrap the dump and front pipe if you can.

yes, you can run a 14..

aim higher..

all the above mods should net you about 190rwkw..

that should be good enough for a 13 of some sort.... with a bit of launch practice..

I had a 34 cooler on my 33. Great upgrade really. And easy to do. I fitted mine in the pouring rain without removing anything but the inner plastic guard in no time. Nissan did us all a favor when they designed the R34's cooler.

Wrap the dump eh? I was going to ask this when I changed mine.... anyway, R34SMIC works well for me. I started on 7psi with the manual ball and spring controller, then 9, now 10psi (as I get bored with the power) Seems to be fine, and power doesn't drop off as though there is massive heat-soak or anything.

I'm yet to hook up a temp probe to check this all out though.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Pressure when IDLING, is meant to be 51PSi... So that amperage value needs to go up a fair chunk... I'd personally be factoring for more like 12amp at least on those runs, and at that point you need to hope the already there wiring doesn't drop you a volt or two, as that's a lot of fuel pressure flow drop off from 13.5 to 12V! Taking idle pressure of 51psi, means the pump will be drawing a MINIMUM of 9amps all the time based on your reading of the graph (3bar base, then allowing an extra 0.5bar for boost = roughly 51psi)
    • Hi all,  I am in the market for an R200 longnose diff out of a Z31 300ZX, or S12 RSX, DR30 skyline, or similar, in a 3.9 ratio.  Preferably a late model one with the M12 crownwheel bolts.  The only easy to find advert for one of these was my ad back in 2007 when I sold it on this forum.  I sold the diff as I had sold the car it goes to, but as it turns out, after 18 years I got the car back late last year, so now I'm looking for the diff !  If anyone knows where to find a longnose R200 LSD with the M12 crownwheel bolts, drop me a line at [email protected] - Bonus paid if soomeone comes up with the original diff (stranger things have happened !).  Cheers   Ben D    
    • Hi everyone, I used to post here a bit from 2004-2013, when I owned various Nissans, in particular my S12 RSX gazelle, which was sold in 2007.  As luck would have it, after an 18 year hiatus, the car found its way back to me last year, and over the past 11 months I have had the pleasure of restoring it with my kids.  One thing that I am after in particular is a 3.9 ratio R200 LSD for it.  I actually sold the one out of the car here back in 2007 , and it would be incredible if I could track down who I sold it to, so I can see how they have progressed over the years (and to be honest, to see whether I can get the diff back !).  Anyways, hi all and let me know "where are the R200 Longnose diffs all at these days ?  Cheers Ben D  
    • Arms will be the same as the G35 or 350Z, but as above, there was a change in the lower control arm where it connects to the ball joint.  That said, you can remove the ball joint cone from your old ball joints and fit them to the new ball joints.  To be honest, I didn't think the ball joints themselves were different. The main ball joint is a bit awkward to replace, you really need to remove the steering knuckle to press out the old one.  Some people have used tools to remove it in place, but it just seemed too hard to get to. If you are going to press out/in that ball joint, then you may as well just replace the bushings in the LCA and the compression rod.  You can buy the compression rod bushing from Nissan, but the LCA bushes, you will need to go aftermarket. Much cheaper than buying the whole arm.
    • Ha, well, it's been.... a bit of a journey. Things have taken much longer than I'd hoped. I'll probably put up a thread at some stage. Hopefully soon. The car's not done any kms since my update in June though, put it that way.
×
×
  • Create New...