Jump to content
SAU Community

Recommended Posts

This guy will do custom ones,

http://grapevine.com.au/~marzenna/

I think he was mentioned on the forum before - maybe there's some feedback on him so try searching.

$150, or $300 if your changing injectors or AFMs. He says you should dyno the car after you install the chip - sensible advice.

Link to comment
https://www.sau.com.au/forums/topic/168938-niztune-chip/#findComment-3136641
Share on other sites

Any tuned chip will give a noticible difference compared to stock which runs rich and has shit timing maps... i had a similar tuned chip in my car for about a year which had a bit of power but ran really rich down low.....

After putting my new turbo, injectors, afm, and all the other supporting mods, CEF11E tuned an eprom chip for me (costing only $50), send it to me, and i put it in and put it on the dyno (normally $50 for a power run but got them to tune my boost controller so it was $150) and the AFMS were PERFECT, the car made a beautiful 230rwkw and CEF11E hadnt even seen the car....

Pretty impressive if you ask me, Cheap as, perfect maps, and ive since done some more mods and he is sending me another chip!

Hes tuning Canberra cars like no tomorrow and a few more sydney cars too!

HAYSEY

Link to comment
https://www.sau.com.au/forums/topic/168938-niztune-chip/#findComment-3137864
Share on other sites

hehe thanks for the plug haysey :domokun:

I would just like to add a bit of information and you can choose to dismiss or take it on board as you like.

Tuning an engine is not something to be done with a few seconds thought. your engine is a valuable piece of equipment and needs to be respected. yes you can buy a remap for your car from ebay but it's a bit like buying a kebab late at night when you are drunk... do you really know what you are getting?

There are people that you can go to and get a professional result:

Dr Drift - Melbourne. really knows what he is doing as is a pioneer, has been doing it for a long time and he is a professional from all the results i have seen.

Speedlab - Jeff - Brisbane? Jeff also knows nissan ecu's backwards and has a lot of proven results and is great to talk to.

Toshi - from these forums also has a lot of results and has been tuning for years since the old schooldays of fj20's in japan.

Yoshitokio - from these forums also has some proven results and has tuned 300rwkw+ cars using the standard nissan ecu.

All these tuners will do a top notch job and you can feel safe shelling out a few bucks to get your pride and joy tuned safely and with fantastic results. they all differ from the fly by night operations that sell a one size fits all tune for $80 bucks from who knows where.

I am by no means a professional and tune for the love of results and interest in performance nissans and I am happy to help forum members out. I have a lot of love for the RB as do all the guys listed above. I have no knowledge of the tunes sold on ebay and do not wish to comment on their merit. But ss the saying goes... pay peanuts, get monkeys...

there is a lot that needs to be done right when tuning nissan ecu's.

Is the chip being used the correct NS rating?

Has the TP scale been set to suit your mods?

what has the tp limit been set to?

What has the rev limit been set to?

Do you have any idea what the timing you will be running be?

seriously ask these questions, it's your engine after all.

Thanks for reading :P

CEF11E

Link to comment
https://www.sau.com.au/forums/topic/168938-niztune-chip/#findComment-3138780
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...