Jump to content
SAU Community

Recommended Posts

I've recently bled the system.

starting at the pump above the rear diff untill fluid came out, closing that and then moving onto the bleed nipple at the transfer case. on and of and on and off untill i had the right levels in the res and untill no air came out. which not much did anyway.

now when driving/under slight acceleration there is always about 1-3kg m or whatever the reading is. it will only go to 0 when i back off completly

is this how the system is ment to work? it feels a bit better than before. and alot more responsive..

:/

Link to comment
https://www.sau.com.au/forums/topic/170507-attessa-system-for-gtr/
Share on other sites

i get about that under medium accel (in a straight line)

slight (just on pedal) accel i get 0 (in a straight line)

cornering tends to bring it back down to 0 until i lose traction (in rear)

hope that explains it a little

RellikZephyr

i get about that under medium accel (in a straight line)

slight (just on pedal) accel i get 0 (in a straight line)

cornering tends to bring it back down to 0 until i lose traction (in rear)

hope that explains it a little

RellikZephyr

ahh thanks. it appears i have bled it alrite then!

slight on pedal i am at around 3 in straight line

:P

ahh, i just got new wheels. same size front/back but different tyres. the rears are a bit worn!

Thats your problem. Try switching the fronts to the rear and vice versa. Should resolve your issue.

Cheers,

Dan :P

I found the exact same thing when I swapped out the rear tyres last wk- as little as 3mm less rear diameter is enough to trigger the ATESSA. Like Angus I'm showing around 1-3-5Kg/m on normal driving & the car responds fantastically when thrown aggressively into corners etc but I am concerned as to what this is doing to the 4WD clutches in the transfer case.

Does anyone have definite knowledge on whether this is damaging or not??

I found the exact same thing when I swapped out the rear tyres last wk- as little as 3mm less rear diameter is enough to trigger the ATESSA. Like Angus I'm showing around 1-3-5Kg/m on normal driving & the car responds fantastically when thrown aggressively into corners etc but I am concerned as to what this is doing to the 4WD clutches in the transfer case.

Does anyone have definite knowledge on whether this is damaging or not??

this is exactly my concern and question!

how good and how responive is the system now!! i'm really enjoing driving the car! this is going from using A048's all the time so i am noticing how the system actually works!

worn tyres that affect rolling diameter will indeed affect attessa , 3-5 mm is enough to cause problems

but all gtrs will throw some torque to the fronts under hard straight line acceleration

if it happens under slight acceleration/cruising then your rolling diameter is the 1st thing to look at

Yeah we know WHY it's doing it, we're both concerned as to what the consequences are.

It really has transformed the way the car drives, & def in a good way but if it's going to be at the expense of the transfer-case clutches then it's obviously not such a good thing.....

yeah rolling diameter :D.....i dont know if it was the cause of a seal on my front diff (right side)to go as the result of having slightly smaller rolling diameter tyre on the rear, and having the above mentioned symptoms??? A bit of a s#^$ to do when done at home on stands. I do have one of the controllers from Duncan..so

does anyone know if having the controller switched to constant RWD only all the time when driving, would it affect anything???I know GTR run in RWD until attessa detects wheel spin in the rear.

But my logic was if i didnt have the attessa working (constant RWD) the leak in the diff wouldnt be as bad, until i got the seal done.

Would anyone else be having the same problem??

I can't see how running in RWD only will help. The power transfer is done at the gearbox & the drive shafts, prop shaft & front diff centre are always rotating when the vehicle is motion, whether there is torque being put to them or not

As for R32/33 transfer cases, I believe they are the same animal but the ACTIVATION is different between the two. The ATESSA computer in the R33 also processes information 4x faster & the combination of the two is why the R32 is in most cases a more "tail-happy" car to drive compared to 33's & 34's.

I'm going to pull the fuse untill further notice about this! but i am loving how the car is driving at the moment.

i've tried to use my field torque controler with knobs turned all the way to rear as possible but it has no effect.

Wow, this is the first time i've ever driven the car without semi's and the system disabled.

4th gear, 80km/h (freeway onramp) around 3000 rpm. plant foot. wait till about 4000ish and i get some serious wheel spin at around 90-100kmh hahaha

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • When I said "wiring diagram", I meant the car's wiring diagram. You need to understand how and when 12V appears on certain wires/terminals, when 0V is allowed to appear on certain wires/terminals (which is the difference between supply side switching, and earth side switching), for the way that the car is supposed to work without the immobiliser. Then you start looking for those voltages in the appropriate places at the appropriate times (ie, relay terminals, ECU terminals, fuel pump terminals, at different ignition switch positions, and at times such as "immediately after switching to ON" and "say, 5-10s after switching to ON". You will find that you are not getting what you need when and where you need it, and because you understand what you need and when, from working through the wiring diagram, you can then likely work out why you're not getting it. And that will lead you to the mess that has been made of the associated wires around the immobiliser. But seriously, there is no way that we will be able to find or lead you to the fault from here. You will have to do it at the car, because it will be something f**ked up, and there are a near infinite number of ways for it to be f**ked up. The wiring diagram will give you wire colours and pin numbers and so you can do continuity testing and voltage/time probing and start to work out what is right and what is wrong. I can only close my eyes and imagine a rat's nest of wiring under the dash. You can actually see and touch it.
    • So I found this: https://www.efihardware.com/temperature-sensor-voltage-calculator I didn't know what the pullup resistor is. So I thought if I used my table of known values I could estimate it by putting a value into the pullup resistor, and this should line up with the voltages I had measured. Eventually I got this table out of it by using 210ohms as the pullup resistor. 180C 0.232V - Predicted 175C 0.254V - Predicted 170C 0.278V - Predicted 165C 0.305V - Predicted 160C 0.336V - Predicted 155C 0.369V - Predicted 150C 0.407V - Predicted 145C 0.448V - Predicted 140C 0.494V - Predicted 135C 0.545V - Predicted 130C 0.603V - Predicted 125C 0.668V - Predicted 120C 0.740V - Predicted 115C 0.817V - Predicted 110C 0.914V - Predicted 105C 1.023V - Predicted 100C 1.15V 90C 1.42V - Predicted 85C 1.59V 80C 1.74V 75C 1.94V 70C 2.10V 65C 2.33V 60C 2.56V 58C 2.68V 57C 2.70V 56C 2.74V 55C 2.78V 54C 2.80V 50C 2.98V 49C 3.06V 47C 3.18V 45C 3.23V 43C 3.36V 40C 3.51V 37C 3.67V 35C 3.75V 30C 4.00V As before, the formula in HPTuners is here: https://www.hptuners.com/documentation/files/VCM-Scanner/Content/vcm_scanner/defining_a_transform.htm?Highlight=defining a transform Specifically: In my case I used 50C and 150C, given the sensor is supposedly for that. Input 1 = 2.98V Output 1 = 50C Input 2 = 0.407V Output 2 = 150C (0.407-2.98) / (150-50) -2.573/100 = -0.02573 2.98/-0.02573 + 47.045 = 50 So the corresponding formula should be: (Input / -0.02573) + 47.045 = Output.   If someone can confirm my math it'd be great. Supposedly you can pick any two pairs of the data to make this formula.
    • Well this shows me the fuel pump relay is inside the base of the drivers A Pillar, and goes into the main power wire, and it connects to the ignition. The alarm is.... in the base of the drivers A Pillar. The issue is that I'm not getting 12v to the pump at ignition which tells me that relay isn't being triggered. AVS told me the immobiliser should be open until the ignition is active. So once ignition is active, the immobiliser relay should be telling that fuel pump relay to close which completes the circuit. But I'm not getting voltage at the relay in the rear triggered by the ECU, which leaves me back at the same assumption that that relay was never connected into the immobiliser. This is what I'm trying to verify, that my assumption is the most likely scenario and I'll go back to the alarm tech yet again that he needs to fix his work.      Here is the alarms wiring diagram, so my assumption is IM3A, IM3B, or both, aren't connected or improper. But this is all sealed up, with black wiring, and loomed  
    • Ceste, jak se mas Marek...sorry I only have english keyboard. Are you a fan of Poland's greatest band ever?   
×
×
  • Create New...