Jump to content
SAU Community

Recommended Posts

I have an R200 Long nose Diff (the one with the speed sensor plug at the end)

Excellent condition, Viscous Centre that's still toight Like a toiger!!!

I run LSD's in mine and have this spare, I bought it as a daily driver then couldn't be assed putting it in...

complete diff $400 Neg.

Call me on 0405284659 for any questions

Cheers

Dave

Link to comment
https://www.sau.com.au/forums/topic/170833-diff/
Share on other sites

Yeh mate, whats the ratio?

These diffs were used in some 260Zs through to R30 and Z31s, and i may be wrong but i think the IRS R31s had it too. As for flanges and the like, there are a million different combos for them, you can usually just swap your old ones into it.

Link to comment
https://www.sau.com.au/forums/topic/170833-diff/#findComment-3159472
Share on other sites

  • 2 weeks later...

Sorry I have been neglectful of the forum of late!

The diff is from a Cefiro, Not mine, I bought it as a daily driver then realised It has the long nose and Mine are all short nose... Nuts to shortening taleshafts so I am selling it.

Its 4:3 I am fairly certain, with 5 bolt outputs, I have never had it in my car, as explained above.

Link to comment
https://www.sau.com.au/forums/topic/170833-diff/#findComment-3181773
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
    • Yeeeppp, been following a lot of the testing on the latest Xona stuff and there are some mental results.  He also went over 1000hp @ 4 hubs on his Mainline with a XRE6364S (63mm) which was also well into the 20psi range before 4000rpm on a 2.5. Crazy stuff. Fwiw the XRE5964S is basically the modern equivalent of their old HTA3582 - would drive nicely enough on an RB25 or 26, but proven capable of a huge amount of power if you want to spicy with rpm tho even at sane boost levels will make stout numbers 
    • The axels in my R33 seem tired, and have a bit of play in them. I cannot find any new of course, not interested in buying used, but I am looking to see if anyone can identify some cross compatible axles. In the states I have seen suggested for S chassis the J30 axles, however for the skyline (as best I can tell) the lengths are about an inch off (2.5cm) on both sides. R33 my measure L 22" R 24.5" GPT L 22.5" 24.25" J30 L 23.5" 25.5"  so shaft length is probably an inch wider. Not sure if someone has another still remanufactured option besides the J30. I figured worst case I can buy a pair tear them down and swap the center shaft. My other option was reaching out to GSP to see if they cannot piece together a set, since the axle stubs are still manufactured, I wouldn't think it be that hard to find a shaft or make a shaft work. 
×
×
  • Create New...