Jump to content
SAU Community

Recommended Posts

Hey, I've got a basically stock 92 r32 gts-t. Months and months ago i got a manual boost controller and turned the boost up to about 12-13psi and more recently i got a 3 inch exhaust with split dump and high flow cat.

It has always run great and loved to be thrashed. But last week on a f**king cold night, i gave it a hit (once the engine was fully warmed) and as the boost started to build, the engine choked. I lost all power and it felt like i was basically just rolling. I had to come off the accelerator to get the power back. This would happen late at nights and early in the morning when it is incredibly cold, but during the day it runs perfectly.

Me and my friend initially thought this was a matter of the stock fuel pump and injectors not being able to match the colder denser air now going into the engine. But the last few days i haven't been able to replicate the problem. It seems to be running fine even on the coldest nights.

What's going on? Why did i have this problem one week, but not the next?

Link to comment
https://www.sau.com.au/forums/topic/171190-power-cut-on-cold-nights/
Share on other sites

did the power cut happen above 4000rpm and was it a missfiring all the up the rev range?

I had similar problem and mechanic said it was crank angle sensor.

It could also be your coilpacks not handling the higher power from the dense air. Check coilpacks for hairline cracks.

sounds like boost cut to me. just means your hitting a point on your ECU map that it considers dangerous and cuts power to the engine. time for aftermarket management, or just take out ~1 PSI to avoid it. if there are other symptoms (like missfiiring through the rev range) could be the coilpacks.. but from what youve said, its just boost cut.

fuel cut wind down the boost so it doesnt cut under all condition i.e cold nights

12 + psi is alot without a cooler on a cold night it could easily spike to over 1 bar

So if down the track i get a cooler, the problem is gonna happen more often?

Im surprised you are running 12psi with only catback and no fmic.

It's preferred that these 2 are modified before any boost is increased because you may be causing a lot of harm.

I suggest drop it back down to 10psi and get supporting mods before you start increasing boost

Im surprised you are running 12psi with only catback and no fmic.

It's preferred that these 2 are modified before any boost is increased because you may be causing a lot of harm.

I suggest drop it back down to 10psi and get supporting mods before you start increasing boost

Hey, I've got a basically stock 92 r32 gts-t. Months and months ago i got a manual boost controller and turned the boost up to about 12-13psi and more recently i got a 3 inch exhaust with split dump and high flow cat.

I got turbo back exhaust.

Just trying to decide which path to take atm.

I really wanna get an fmic, but if i do that then i definately have to get an ecu. And after that i'm gonna want more and more power because i know i can have it. So it's gonna cost me alot in the long run.

Alternatively i could turn down the boost and save my money. But stock power is sooooo boring.

Getting an fmic does not warrant an ecu...although some sort of ecu will probably be best...if you keep your boost to 12psi...i don't see any problem...provided you are not running mixtures that are too lean...have you got a fuel pump yet? if not...i'd get one asap...even before considering a fmic...fuel pumps on 32s are VERY old now and will most likely be on their way out....

Edited by limpus

Can the power drain on the battery cause this?

I have had this happen to me...twice so far.

On cold nights....my heater,power fc,AVCR ,air purifier..stereo/amp/sub...lights...are all on.....

Can the drain in the power and a bad battery be at fault.

The battery in the boot is tiny and due to workshop downtime has been drained at least 10 times....

The only thing I think that keeps it firing every morning is the turbo timer charging it the night before..lol

It sounds like it is electrical...if you know your battery is good...check your coils....spark plugs.

This can also be a AFM fault.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After using a protractor for an actually accurate assessment of what is required,  and by NOT using my uncalibrated eyeball I worked out I need a 25° silicone bend from the TB ro the MAF, but, my choice was either a 30° or a 23° (23° is a weird spec), so I grabbed the 23° one from Raceworks I also grabbed 1mtr of 3" straight from Just Jap, I needed 350mm, but they only had 300mm, or 1mtr lengths....meh Also ordered a 1/2" hose bulkhead fitting from fleabay, this has a smoothish mushroom looking head (they are designed for below the water line of boats) that will fit inside the bend, the hose bit and threaded bit looks to long, but nothing that a hacksaw cannot fix if required, the hose will then just get jamed on the threaded bit up to the retaining nut Fingers crossed and the unsightly amount of hose clamps will be reduced down to 4 once all the parts arrive 
    • Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
    • No. I think it might be the AFM. Hence the use of the terms "swaptronics", which implies the use of swapping out electronics for the purpose of diagnosis. It's about the only way to prove that a small/niggling/whatever problem with an AFM or a CAS or similar is actually caused by that AFM/CAS/whatever. A known good item swapped in that still gives the same problem is likely to be caused somewhere else. They're all the same. Spraying AFMs with cleaner is an each way bet between cleaning it and f**king it.
    • Oh wow! This might actually work amazingly. Do you know the ratio of the diff? I was told the only thing you need to make sure of is if the front & rear diff ratios are the same. Ours is a 4.083 Thanks!
×
×
  • Create New...