Jump to content
SAU Community

Recommended Posts

am wrecking a 90 R32 Gtr

will put up a list of buyable parts once i pull them off

until then hit me up and ill let you know if i can get the part

Location is Central queensland

Parts being held

Attesa oil pressure switch

pod filters and necks

A/C surround

rear speaker covers

boot trims

rear seats

drivers side seat belt assembly

steering wheel

AC centre vent

boot lid

rims and tyres

roof lining

front calipers + discs

diff

damage is to Passenger side wheel area most of the rest of the car is ok hope that will do for viable parts list

please all inquires via PM

also im working 12 hour shifts for approx 2 weeks longer so bare with me might take a little time for things to go along smoothly

Cheers

RellikZephyr

Edited by RellikZephyr
Link to comment
https://www.sau.com.au/forums/topic/171597-wrecking-32-gtr/
Share on other sites

All PM replied

sorry have been rather busy

please all queries via PM makes it bit easier (wasnt expecting so many queries so quickly)

ok parts being held

Attesa oil pressure switch

pod filters and necks

A/C surround

rear speaker covers

boot trims

rear seats

drivers side seat belt assembly

steering wheel

AC centre vent

Location is Central queensland for those that asked

am replying to all posts now via PM

sorry for lengthy replies

RellikZephyr

Link to comment
https://www.sau.com.au/forums/topic/171597-wrecking-32-gtr/#findComment-3166989
Share on other sites

all replies responded to via PM

sorry for slow replies

12 hr shifts 6 days a week and night shift stupid shut downs

almost finished approx 2 weeks more

but got this week end off so i will get into it for all parts being held

Thanks for your patience

RellikZephyr

Link to comment
https://www.sau.com.au/forums/topic/171597-wrecking-32-gtr/#findComment-3167036
Share on other sites

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Hi. This is just my curiosity because iam sure the tuner figure something out...but either way i want to ask. The "problem" is that the Nistune ECU (Stagea FW and RB25DET NEO from Stagea) sees many times the speed than the speedo does(he says the speedo show 120 km/h - correct speed and the ECU shows like 510km/h ) I told him that this car/tranny getting speed from rear diff. If iam not mistaken the RB25DET NEO "need" to see tranny speed sensor? (my tranny has the plug for it). So couple of "question" If he connects/wire the speed sensor to the tranny...are the signals gonna intervene and if...what if he disconnects the rear diff one and the speedo stops working? Or the "new" sensor from the tranny "take over" and will not going need the one from diff? As i said i know he figure/get that done...iam just curious to know what are the solutions 🙂 
    • Your IACV is set to idle too low. You need to adjust it via the screw Duncan mentioned. From memory it should be 650rpm with the valve electrics unplugged. What is it trying to idle at with the IACV plugged in?
    • Ahhh, I need the whole head unit. I definitely needed to roll back through and review your setup, ha ha! Neat setup they have going on. I just need a full double din head unit. But I want good and responsive. I might have to review what the likes of pioneer have out these days.
    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
×
×
  • Create New...