Jump to content
SAU Community

Eqi: R32 Door Sill Plates (stainless Steel)

subie

By subie,
in Group Buys

 Share

Recommended Posts

subie Grand Master

subie

Posted
  • Author
Posted

RB POWER I like it mate..

I have to order one set first, so I can take some photo.. but this set gonna cost me more than the rest of it! That why I need a group buy otherwise I just get a set for myself!

will see what i can do to get some pics!

Blitz Grand Master

Blitz

Posted
Posted

As per the group buy rules, please update your first post to include details of the supplier providing these for the group buy, and also the start and end date.

Thank you

subie Grand Master

subie

Posted
  • Author
Posted
As per the group buy rules, please update your first post to include details of the supplier providing these for the group buy, and also the start and end date.

Thank you

Hi mate,

this is just an eqi to see who interested and will comfirm the date of start and end dates the end of this month..

and the supplier is from oversea will confirm that aswell

Cheers

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • Kinkstaah
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Kinkstaah · Posted

      You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
    • Dose Pipe Sutututu
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Dose Pipe Sutututu · Posted

      LOL.... you are correct there.
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      It's been quite the ordeal but hey, at least you figured it out.
    • The Bogan
      NC MX5

      By The Bogan · Posted

      The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
×
×
  • Create New...