Jump to content
SAU Community

Fitting T1.25 Led Replacement Globes To R32 A/c

666DAN

By 666DAN,
in Tutorials / DIY / FAQ

 Share

Recommended Posts

666DAN Grand Master

666DAN

Posted
Posted

Unclip the front cover

Picture005-1.jpg

Remove the 3 screws holding the button section to the unit and remove the button section.

Picture006.jpg

Remove the 2 screws holding the board in place. Push the back of the 4 lights either side of the gang connector to the right of the display. This will push the board out from behind and unclip it from the connector.

Picture007.jpg

Remove the globes

Picture010.jpg

Fit the LEDs, they’re very snug and may click into place, once in, rotate them to lock them into place, may be easier to push with your finger nail.

Picture011.jpg

Picture012.jpg

Push the board back onto the connector, plug the unit in to make sure all the LEDs are the correct way around an illuminate. If any don’t light up note which ones they are and replace them turning them 180 degrees. Retry and confirm you’ve got them all the right way around.

Now there are 2 options, you can either remove the light diffuser so the LEDs don’t foul on the inside of the unit (some clever angling of the LEDs will get perfect dispersion), or modify the light diffuser by drilling/melting out the section where the LEDs line up.

Picture008.jpg

Picture028.jpg

Once done, replace the screw and put back together (reverse of taking apart)

subie Grand Master

subie

Posted
Posted

Hi Dan,

Now there are 2 options, you can either remove the light diffuser so the LEDs don’t foul on the inside of the unit (some clever angling of the LEDs will get perfect dispersion), or modify the light diffuser by drilling/melting out the section where the LEDs line up.

what does this mean? do i have to do this? and why?

Cheers

666DAN Grand Master

666DAN

Posted
  • Author
Posted
Hi Dan,

what does this mean? do i have to do this? and why?

Cheers

The lights being so bloody tiny in tungsten form only have a small area to sit, with the LED type they are slightly bigger so need some extra room made behind the diffuser...this is the only option I'm afraid.

Dan

  • 1 month later...
  • 5 weeks later...
LoNg_ShaNks Community Regular

LoNg_ShaNks

Posted
Posted
would i loose much light if i removed the light diffuser? intead of drilling/melting it down?

what he said? can any1 confirm which method works best?

oh and pics of finished results would be awesome to :)

hazerb30 Collaborator

hazerb30

Posted
Posted

Ok, just did mine last night. You need patience to do this.. it kinda gay for something that should be easy.. how many people does it take to change a light globe kind of thing.

So.. I pulled out the A/C unit. Took the front cover off it and Unscrewed the circuit board. Spent a few mins figuring out how to get the circuit board out ( you do need to get it out). Take 666dans advice here and use a screw driver and push on the back of the old globes and the circuit board pushes out with them.

so.. i put em all out and put the LED ones in (either use your thumbnail or a large flat blade screwdriver to push and turn them in) Went back to the car with it in pieces still and tried it out. Shit.. i was unlucky with the 50/50 chance and got them all the wrong way. Pulled it out and turned all the LED's around the other way. Test again.. they all lit up. Hey they are really bright!

So thats kool. Now to get the cover back on. It wont fit with clear plastic diffusers in place so i took them out and tried it out in the car again. Wow that looks totally shit.. can barely see most of the lights and one is stoopidly bright. This is the point i went inside and read this tutorial properly. hmmm... seems that people had sucess with moving the LED's so they point in certain directions.. tried this and it looked better but still crap.

Well, looks like ill have to modify the diffuser. If you try and keep the diffusers in there with the LED's it will just squash them and pop them out of the socket. you DO need to make more space for them. Now i thought i would be a smarty and file the end of each LED down using sandpaper and that would give them enough room so sit in there. It would also disperse the light better. Nope.. it was a lot closer but still not enough room. Used a drill and VERY VERY carefully drilled down until i was just touching the 'V'. This will only make sense once you look at the diffuser closely. Tried it again. all good.

Final results.. it works and i can see the buttons now. Its not very bright though but thats a good thing. If i could find the stock globes i would buy them to save most of this hassle but it does look ok

DaShMiEsTeR Enthusiast

DaShMiEsTeR

Posted
Posted
the exciting part about it is that i can actually SEE the controls now. Before this i was fumbling around in the dark pressing all the buttons. Colour does match the dash cluster now :thumbsup:

looks awesome bro!

  • 1 month later...
  • 2 weeks later...
  • 3 weeks later...
POL44K Enthusiast

POL44K

Posted
Posted

i bought normal globes from genuine holden spare parts they're exactely the same except with a black base an green sleeve, i think they're in VT's but just take the globe to em an they'll know

  • 1 year later...
  • 2 months later...
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Murray_Calavera
      Jacks that fit under GTR lips that can reach the subframe?

      By Murray_Calavera · Posted

      My dream is also to have a proper hoist, but I don't think it will ever happen. My quickjack is probably as close as I'll ever get, it really is very good though. 
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      Yeah we keep on in the dailies, it is pretty poor how many animals get hit and the driver leaves without checking....have saved a couple of little ones over the years. Bit of a gruesome job though, pouches generally need to be cut open because they are so tight and often the joey doesn't realise mum is gone so they are still locked onto the teat. I checked the modules in front of the DS wheel where an oil cooler should go.... There is the radar unit - that can go for race use) One of the 2 HX water pumps, the silver cylinder. That needs to be kept but might be able to be relocated But the bad news, the big computer mounted vertically in front of the wheel (blocking any potential air exit) is the electric steering computer. That is required until/unless i do a hydraulic steering conversion, and in CAD based modern car design it is not like I can just pop a big unit like that somewhere else (plus the loom would be too short anywhere else too). So, the passenger side is OK to clear out (just use a smaller washer reservoir, potentially elsewhere), but the DS no beuno
    • Duncan
      Chris' Toyota Mark ii JZX110

      By Duncan · Posted

      Well, all the best with the new camry It was interesting to hear about the UK process, it is generally a lot more streamlined here with a shipping agent looking after all the import side (noting the exact final price can still be a surprise.....) and I've used a few different brokers on the japan (or US) side, and never had any trouble with any of them....luck of the draw I guess. You mentioned you didn't get the auction sheet (understandable since you bought it from a dealer, not auction), but I always try and get hold of that because they are pretty thorough. I've imported 2x R grade vehicles over the years and both were fine, repairs in Japan are pretty thorough compared to here in Oz.
    • Duncan
      Jacks that fit under GTR lips that can reach the subframe?

      By Duncan · Posted

      BTW I measured the jack I have, it is 70mm at the saddle but you only have about 700 until it returns to 150mm high at the cylinder so it is good but no magic bullet.
    • hoodedreeper
      Chris' Toyota Mark ii JZX110

      By hoodedreeper · Posted

      My experience with Rising Sun Exports Before agreeing to the sale I tried to do as much research as I could (obviously), his Facebook reviews are 98% and he goes Live at least once or twice a week. I contacted 2 people in the UK who had used him for their imports, both had positive feedback. His explanation and talk through of the import process was thorough, answering any query no matter how stupid it was. It felt as soon as the money was sent, communication dropped off. I asked for shipping updates every 2 weeks or so, not wanting to pester him, he never had any updates. I wasn't informed the car had been dropped off at the port, I only found out by his Facebook story. I asked for the photos taken at the port, knowing he would need some for insurance purposes. I received a few 5 second clips and that's it. When asked again, he said his staff had them. Weeks later I asked again, he tells me he doesn't have any, but does have 50 photos from the original advert. I never received them. I eventually got the documents sent via WhatsApp after I mentioned the port was requesting them. I purchased a CarVX report, to find out the vehicle is a Grade R with recorded accident damage, first recorded in 2017 when it was first auctioned. He never told me the grade, then again I didn't ask. His response was "Grade R means nothing, it wasn't chassis damage". Still, I would have liked to have been informed about it. Jon prides himself on being open and honest when it comes to inspecting cars, it's his main job doing so at the auctions for customers. When the vehicle arrived in the UK I noticed a few little cosmetic issues. It's a 21 year old car so it wasn't going to be mint condition. The side skirts are cracked on each corner and the sealant is failing. The front grill on the bonnet/hood isn't secured very well, mounting studs are missing. Both minor things, but again, it would have been nice to be told. During a Facebook Live walk around video of the vehicle, he mentioned it has a front Whiteline anti roll bar/sway bar. While on the inspection ramp, I noticed the stock item has been installed. When first questioned, his response was "the ARB? Switched? Since when, it never had them". Since sending video and photo evidence I've not received a response. I'm probably being over critical of the overall condition of an old car, but all I wanted was honesty (which he claims to have). I'm aware I wasn't his only customer, he's busy doing XYZ but other reviews praise him for great communication with regular updates and photos, I felt I didn't receive the same treatment. 
×
×
  • Create New...