Jump to content
SAU Community

Recommended Posts

G'day everybody!

As the title states i hit something while doing something naughty. Cut a long story short got a new rim and put it on but now the 4WD and ABS lights are on! When i was waiting for a new rim i disconected the battery only then the light came on. I have checked the for error code and it's 13.

I have search but only came up a few solutions like...

-Check the sensor close to hand brake (Done it's still white)

-Check the conections under car? (not yet waiting till day off)

Thats all i have come up with If you could give me a hand that would be swell!!

You may have damaged one of the wheel sensors which will bring those lights on.

Wheel sensor? is that in the wheel hub itself? Some direction would be appreciated.

Also is it possible for me to just swap the wires so the two back ones are reading the same?

One more are the sensors the same across the range eg R33 GTST and GTR? (I have a R32)

Wheel sensor? is that in the wheel hub itself? Some direction would be appreciated.

Also is it possible for me to just swap the wires so the two back ones are reading the same?

One more are the sensors the same across the range eg R33 GTST and GTR? (I have a R32)

I'm sorry for the little rant here but it seems to me that there is alot of unanswered questions in the furums lately... So much knowlege at hand here and no one wants to share!

whiteboy01, you posted here > http://www.skylinesaustralia.com/forums/in...howtopic=157022 ..

Did you read the response?

Do the diagnostics.. use what nissans engineers gave you to find the fault.. not everyone's a genius.. we're all learning.. common sense all the way..

Abs sensors are on all 4 hubs , they pick up a signal fron the toothed rings around the hubs . Its possible with the smash the sensor is broken .

Were abouts are these sensors? Here is a pic i made in Paint were should i be looking couldn't find anything.

post-36471-1181974133_thumb.jpg

hope this helps lol..drawing from memory....its a plug there on the hub..just in front of where the cv boot is attached ..you should be able to see the toothed grooves there..the sensor i think is a magnet at the end of it..grease n dirt can get in there and could be the cause perhaps??or become loose?

post-24749-1181981285_thumb.jpg

heller44: Yer i did follow the instructions all the way though but some things that i couldn't see right (plus i was tired) i will try again. though some tests keep pointing to a G-Sensor 1 and thats near the hand brake and should glow red when broken but it was fine (glowing white).

Godzl1975 i will have a good look tomorrow is this a common fualt with this sensor? Can i just grab another one from some other skyline R33 GSTT?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, version 4 intake is on its way I was looking at these a while ago but at around $200 or more it was a little pricey for something that might not work, but, I had it in my watch list, but, I got a message saying it was on special, and I had a code thingie to use, it eventually came in at $120 delivered, so BAM, BUY NOW.....LOL I'll need to have a look when it arrives but I feel it will "look" better than what I currently have, as it comes with a PCV fitting, so I will be able to get rid of the alloy pipe that goes to the throttle body with the PCV fitting  Well, that's what the voices in my head are telling me  Oh, and this happened today Yeap, it was a Trojan, and it was cheap, so I headed back to the hardware store and actually spent a little bit more on a heavy duty,  one that was actually recommended by a plumber mate, a Cyclone one with a fibreglass handle that is actually rated for clay The broken shovel will eventually be "modified" into a short handle shovel
    • When you pulled it off, there is no signs of blown head gasket? Is it possible you have some other issues going on? Possible cracked blocked? Or do you think it's straight up lifting the head? Did you check what the head was torqued to before pulling it down (To see if possibly they're stretching, or starting to break threads out etc)?
    • Seems like a decent result for a modded JZX110. They are bulky in comparison to the 100 and 90 models (which I'd prefer myself) but they are getting very few and far between here in JP these days. Thanks for the detailed review and the import process into the UK. I also have a car which I'm hoping to export from Japan at some stage so it's good to know if someone from the UK was interested in it. By the way the corrosion underneath is par for the course for cars which were located in/near the mountains or along the Japan sea coastline. They get huge amounts of snow every winter and the sodium chloride is used on the roads. Many cars have some kind of rubber like treatment underneath but they tend to limit it to the wheel arches underbody and fuel tank. Suspension arms and sub-frames will have similar corrosion to your JZX110 which is a common sight. See it all the time and car dealers here generally don't even mention it unless asked.
    • If the sound goes away when you clutch in, the 1.5/2 way diffs are just shit, and you are a normal person. The diff is likely "fine" but driving at anything under 30kmh is a violent horrible experience. It would be exaggerated with solid diff bushings and subframe bushings if you have those.
×
×
  • Create New...