Jump to content
SAU Community

Recommended Posts

  • Replies 121
  • Created
  • Last Reply

Top Posters In This Topic

copied from the Japanese who wanted to look different - just a whole lof of "me too"

if it actually functioned better the recommended fitments from manufacturers would reflect a 225 width tyre on a 10" rim.

all motorsport has tyres which fit the rim properly - eg. V8s, touring cars, F1 etc etc.

Link to comment
https://www.sau.com.au/forums/topic/173783-stretched-tyres/#findComment-3192520
Share on other sites

yeh, like he said, it's got no real practical purpose but to look cool

I guess on drift cars, the less tyre on the road (at the back) = the better, so stretched tyres = less on the road (because they bulge in the middle)

from a grip standpoint, your getting less tread on the road though

Link to comment
https://www.sau.com.au/forums/topic/173783-stretched-tyres/#findComment-3192554
Share on other sites

yeh, like he said, it's got no real practical purpose but to look cool

I guess on drift cars, the less tyre on the road (at the back) = the better, so stretched tyres = less on the road (because they bulge in the middle)

from a grip standpoint, your getting less tread on the road though

although on high speed corners it feels like there is less flex in the wall. i just got new tyres (un streatched) 225 and it is now apparant on corners that the tyre has a little bit more give in it. just my two cents.

Edited by GTS_Retro
Link to comment
https://www.sau.com.au/forums/topic/173783-stretched-tyres/#findComment-3192598
Share on other sites

yeh retro, there will be alot less sidewall on stretched tyres, so less movement, but better to just go a lower profile and have the same size footprint on the road, like you've done now, than stretch the crap outta them and scrooge up your traction

Edited by r32 gts-turbo
Link to comment
https://www.sau.com.au/forums/topic/173783-stretched-tyres/#findComment-3192648
Share on other sites

also stretched tyres means you can have a wider rim under the car as it won't hit the guards as easily.

Wheels are there to hold your tyres. What's the point of running a wider rim if you're not going to use that width to crowd more tyre onto? All that extra metal would be unsprung ballast.

Link to comment
https://www.sau.com.au/forums/topic/173783-stretched-tyres/#findComment-3193726
Share on other sites

Wheels are there to hold your tyres. What's the point of running a wider rim if you're not going to use that width to crowd more tyre onto? All that extra metal would be unsprung ballast.

a lot of rims don't come in skinny sizes, and cars like sprinters don't have much room under the guards

Link to comment
https://www.sau.com.au/forums/topic/173783-stretched-tyres/#findComment-3193884
Share on other sites

anyone know if 234/45/17 can be stretched onto the rear 8.5 inch wide rims?

Yeah, shouldn't be an issue.

I've stretched a set of RT215s in that dimension onto a 9.5" wide rim, and even with the amount of abuse I've put the car through I haven't had any problems.

Link to comment
https://www.sau.com.au/forums/topic/173783-stretched-tyres/#findComment-3195363
Share on other sites

I have 235/45/17 on 9 inch wide rims. Reason - they came that way. And when i replaced the tyres i was scared that any wider would rub.

So you will be fine, i've driven over 100,000km in my r32 with these sized tyres. Its the extreme streching you have to be wary of.

Link to comment
https://www.sau.com.au/forums/topic/173783-stretched-tyres/#findComment-3195673
Share on other sites

Its all about side wall flex and eliminating it. With stretched tires there will be less if any side wall flex which makes the car more predictable and easy to control when drifting.

Also an easy way to fit bigger wheels inside your guards instead on flaring or scrubbing!

Link to comment
https://www.sau.com.au/forums/topic/173783-stretched-tyres/#findComment-3196219
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • And finally, the front lower mount. It was doubly weird. Firstly, the lower mount is held in with a bracket that has 3 bolts (it also acts as the steering lock stop), and then a nut on the shock lower mount itself. So, remove the 3x 14mm head bolts , then the 17mm nut that holds the shock in. From there, you can't actually remove the shock from the lower mount bolt (took me a while to work that out....) Sadly I don't have a pic of the other side, but the swaybar mounts to the same bolt that holds the shock in. You need to push that swaybar mount/bolt back so the shock can be pulled out past the lower control arm.  In this pic you can see the bolt partly pushed back, but it had to go further than that to release the shock. Once the shock is out, putting the new one in is "reverse of disassembly". Put the top of the shock through at least one hole and put a nut on loosely to hold it in place. Put the lower end in place and push the swaybar mount / shock bolt back in place, then loosely attach the other 2 top nuts. Bolt the bracket back in place with the 14mm head bolts and finally put the nut onto the lower bolt. Done....you have new suspension on your v37!
    • And now to the front.  No pics of the 3 nuts holding the front struts on, they are easy to spot. Undo 2 and leave the closest one on loosely. Underneath we have to deal with the wiring again, but this time its worse because the plug is behind the guard liner. You'll have to decide how much of the guard liner to remove, I undid the lower liner's top, inside and lower clips, but didn't pull it full off the guard. Same issue undoing the plug as at the rear, you need to firmly push the release clip from below while equally firmly gripping the plug body and pulling it out of  the socket. I used my fancy electrical disconnect pliers to get in there There is also one clip for the wiring, unlike at the rear I could not get behind it so just had to lever it up and out.....not in great condition to re-use in future.
    • Onto the rear lower shock mount. It's worth starting with a decent degrease to remove 10+ years of road grime, and perhaps also spray a penetrating oil on the shock lower nut. Don't forget to include the shock wiring and plug in the clean.... Deal with the wiring first; you need to release 2 clips where the wiring goes into the bracket (use long nose pliers behind the bracket to compress the clip so you can reuse it), and the rubber mount slides out, then release the plug.  I found it very hard to unplug, from underneath you can compress the tab with a screwdriver or similar, and gently but firmly pull the plug out of the socket (regular pliers may help but don't put too much pressure on the plastic. The lower mount is straightforward, 17mm nut and you can pull the shock out. As I wasn't putting a standard shock back in, I gave the car side wiring socket a generous gob of dialectric grease to keep crap out in the future. Putting the new shock in is straightforward, feed it into at least 1 of the bolt holes at the top and reach around to put a nut on it to hold it up. Then put on the other 2 top nuts loosely and put the shock onto the lower mounting bolt (you may need to lift the hub a little if the new shock is shorter). Tighten the lower nut and 3 upper nuts and you are done. In my case the BC Racing shocks came assembled for the fronts, but the rears needed to re-use the factory strut tops. For that you need spring compressors to take the pressure off the top nut (they are compressed enough when the spring can move between the top and bottom spring seats. Then a 17mm ring spanner to undo the nut while using an 8mm open spanner to stop the shaft turning (or, if you are really lucky you might get it off with a rattle gun).
    • You will now be able to lift the parcel shelf trim enough to get to the shock cover bolts; if you need to full remove the parcel shelf trim for some reason you also remove the escutcheons around the rear seat release and you will have to unplug the high stop light wiring from the boot. Next up is removal of the bracket; 6 nuts and a bolt Good news, you've finally got to the strut top! Remove the dust cover and the 3 shock mount nuts (perhaps leave 1 on lightly for now....) Same on the other side, but easier now you've done it all before
    • OK, so a bunch of trim needs to come off to get to the rear shock top mounts. Once the seat is out of the way, the plastic trim needs to come off. Remove 2 clips at the top then slide the trim towards the centre of the car to clear the lower clip Next you need to be able to lift the parcel shelf, which means you need to remove the mid dark trim around the door, and then the upper light trim above the parcel shelf. The mid trim has a clip in the middle to remove first, then lift the lowest trim off the top of the mid trim (unclips). At the top there is a hidden clip on the inner side to release first by pulling inwards, then the main clip releases by pulling the top towards the front of the car. The door seal comes off with the trim, just put them aside. The the lighter upper trim, this is easy to break to top clips so take it carefully. There is a hidden clip towards the bottom and another in the middle to release first by pulling inwards. Once they are out, there are 3 clips along the rear windscreen side of the panel that are hard to get under. This is what the rear of the panel looks like to assist:
×
×
  • Create New...