Jump to content
SAU Community

Fitting The 1000/sec Refresh Attesa To A Bnr32

GeeTR
 Share

Recommended Posts

GeeTR Grand Master

GeeTR

Posted
Posted

Hey yall,

Been a thought iv had for years, thought it would be worth to throw it out there.

Say im looking for something more from a BNR32, what would be required to get my ATESSA up to scratch. Using a G-force sensor bender is a bit old hat, and doesn’t change the fact the system is clocking 10 times a second.

What do you think is required to get a R34 / 33 system into a BNR32?

Would the diff chassis lengths (hence torque application software) make it not work? Would i need to change transfer cases, or could simple ECU and sensor changes suffice?

Thoughts, opinions flames???? :yes:

M

paulr33 Grand Master

paulr33

Posted
Posted

an alternative could be to get a GRID dancer controller or hks ETS controller and upgrade the 4wd clutch packs to make it stronger

you could also look at locking the pump on via a relay interceptor if you have the vspec system (i did this in my gtst)

GeeTR Grand Master

GeeTR

Posted
  • Author
Posted
an alternative could be to get a GRID dancer controller or hks ETS controller and upgrade the 4wd clutch packs to make it stronger

you could also look at locking the pump on via a relay interceptor if you have the vspec system (i did this in my gtst)

Yah, unfortunately,

Using a G-force sensor bender is a bit old hat, and doesn’t change the fact the system is clocking 10 times a second.

The ATTESA system as a concept is one that’s used now by most of HiPo manufactures like Porches etc. I don’t want to lock it solid, front to back, nor simply strengthen the clutch packs, Iv never driven a R34 GTR, but am told the system is a lot more progressive and adaptive to wheel spin, and how tight it push’s the packs together. You can watch from footage of quick examples how it effects the attitude of the car (understand the E-diff has a role here, but lets leave that out of the equation for now)

Any other thoughts

sav man Grand Master

sav man

Posted
Posted

Is the R23 V-Spec II a 1000/sec ecu, or was it just a retuned 100/sec ecu? The probelm I see with a R33/R34 ecu is that they have 10% always going to the front wheels, and if you put one of those ecu's in a R32, it would expext 10% to always be there.

Our Targa car has a HKS Kansai controller, no idea how good it is cause we've never turned it on (came with the car), if anyone has any english instructions i'd appresiate it.

Duncan Grand Master

Duncan

Posted
Posted

Unless the controller replaces the attessa computer completly it can't refresh quicker. I've never seen the Bee-R ones but the grid and all the locally made ones like ours leave the standard computer in place

GTS4WD Grand Master

GTS4WD

Posted
Posted
Is the R23 V-Spec II a 1000/sec ecu, or was it just a retuned 100/sec ecu? The probelm I see with a R33/R34 ecu is that they have 10% always going to the front wheels, and if you put one of those ecu's in a R32, it would expext 10% to always be there.

Stupid question..

but..

Why?

This does answere MANY MANY questions! I went staggy RB25 + ECU in my GTS4 and.. GUESS WHAT!?!.. 10% all the time..

..ghay..

Any way you cans stop/change it?

sav man Grand Master

sav man

Posted
Posted

I think the trasferbox is designed diferently. As you have to remove the front shaft to dyno R33+, and not just the ecu fuse. well 10% is sfa in the grand sceme of things, i assume it balenced the car a little better, and it would make the attessa feel more responsive. The R32 one can feel a little slow at times.

Did you do the gearbox/trasfur case with the engine and ECU?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...