Jump to content
SAU Community

Recommended Posts

Hey all,

I've got a 1990 R32 Gtst with 217rwkw and an NPC brass button clutch. I had some trouble a while ago with the clutch not disengaging properly i.e. when pulling up to a set of traffic lights with my foot on the clutch and brake pedal, the car would lurch forward slightly and want to "drive on." I would then have to reef the gear stick out of first gear and in to neutral, and then back into first and then it would be ok untill I had to pull up at another set of lights etc. Initially I put this down to the heavy pressure plate in the car, however i took the car back to my workshop and had them change the pressure plate to a lighter one. The car was then alot more driveable on the street and the problem seemed to go away, until a couple of days ago and it has gradually gotten worse. I can't come to a stand with my foot on the clutch without having to reef it out of gear when I stop. I have changed both the Master cylinder and slave cylinders a few months ago and the clutch system doesn't appear to be losing any fluid, I have bled the system correctly and now I am at a loss. I was wondering whether anyone else has come across anything similar and any help would be greatly appreciated.

Cheers Dylan

Link to comment
https://www.sau.com.au/forums/topic/177013-r32-clutch-troubles/
Share on other sites

You may need to pull the peddle box out and check to see it hasnt broken any spot welds on it, could be possible that the box is now flexing when you put your foot on the clutch and not acctually pushing the clutch in far enough.

Other issue may be master or slave, i know you said you replaced them but were the replacements brand new? If not then whats to say there isnt a problem there.

Finally, in the middle section between the master and slave theres the box with lines going in and out of it and a bleed nipple..piss this section off all together and just run a line from the master to the slave, then bleed starting from the master followed by the slave.

Did you machine the flywheel when changing the clutch?

My guess is the flywheel is worn into a funnel shape (only very slightly, probably invisable to the eye). So when you shove the pedal in the clutch plate is still grabbing along the outside edge..

If the flywheel is fine, perhaps there is a physical defect in the pressure plate. Or maybe you have a mismatched clutch bearing (happened to me, I was supplied a bearing slightly shorter than what was required, and the outside clips on the bearing were hitting the solid edge of the pressure plate).

Hope that helps. Clutches can be a real pain. :blink:

I had a similar problem to this once and it was the slave cylinder was bleeding back, seals were on there way out, the more it got used the worse it was but recovered when driven for a while and clutch not used had me buggered for months till I found it ,just wouldnt travel full length same can happen to mastercylinder ...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
    • Sorry, just assumed that talk of coloured pads meant EBC red/green/yellow/shit stuff. I don't know the DBA pads, but it's a reasonable bet that they will be OK. DBA make good stuff generally. Those 4000 series rotors I linked to are very good. I may well replace the RDA rotors I have with those when required.
    • The average previous owner for these cars were basically S-chassis owners in the US. Teenagers or teenager-adjacent. I often tell people that neglect is easier to fix than something that was actively "repaired" by previous owners.
    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
×
×
  • Create New...