Jump to content
SAU Community

Recommended Posts

Hey guys.

Just wonering if anyone around Sydney has performed the light change for the A/C

I got the bulbs off Dan but i don't know how i can solder these on etc.

I will drive there if you can help me.

Please gimme a hand if you can.

Please contact me on 0433 230 959

Paul

Link to comment
https://www.sau.com.au/forums/topic/177019-help-with-replacing-ac-lights/
Share on other sites

Hey guys.

Just wonering if anyone around Sydney has performed the light change for the A/C

I got the bulbs off Dan but i don't know how i can solder these on etc.

I will drive there if you can help me.

Please gimme a hand if you can.

Please contact me on 0433 230 959

Paul

I'm pretty sure there is a DIY on this in the DIY section..

If you're talking about http://www.skylinesaustralia.com/forums/in...=172061&st=

I've already read it and it doesn't help as the lights are different ;)

Just need to know if anyone around here has done this possibly on a R34

If you're talking about http://www.skylinesaustralia.com/forums/in...=172061&st=

I've already read it and it doesn't help as the lights are different ;)

Just need to know if anyone around here has done this possibly on a R34

What kind of bulbs are they?

did you see this thread

http://www.skylinesaustralia.com/forums/in...howtopic=172056

there was final pics of the lights in evesdropping first reply

i haven't done it yet, still have to buy the LEDs

The lights aren't exactly the same as the ones in Dan's thread.

The lights i have are longer and hence i need to chop off the base of the light if i was to use the existing holders.

Don't know if i can cut these off though :)

Just an update guys.

I managed to fit them in with no soldering required.

Might write up a DIY when i have time.

All i did was to trin down the LED base and the OEM holders and wire up the wires into the factory holder positions.

Then i simply screwed them back in and wallah!

WOOT WOOT!!!

All looks good now.

Thanks for the offers guys.!!!!

isn't that what it said to do in the DIY thread?

If u have a R34, u know the globes will not fit in the holders no matter how much trimming is done.

I had to improvise and just let it hang on to the holders with th wires holding it in place.

If u have a R34, u know the globes will not fit in the holders no matter how much trimming is done.

I had to improvise and just let it hang on to the holders with th wires holding it in place.

I see...

It looks pretty good a?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
    • Yeeeppp, been following a lot of the testing on the latest Xona stuff and there are some mental results.  He also went over 1000hp @ 4 hubs on his Mainline with a XRE6364S (63mm) which was also well into the 20psi range before 4000rpm on a 2.5. Crazy stuff. Fwiw the XRE5964S is basically the modern equivalent of their old HTA3582 - would drive nicely enough on an RB25 or 26, but proven capable of a huge amount of power if you want to spicy with rpm tho even at sane boost levels will make stout numbers 
    • The axels in my R33 seem tired, and have a bit of play in them. I cannot find any new of course, not interested in buying used, but I am looking to see if anyone can identify some cross compatible axles. In the states I have seen suggested for S chassis the J30 axles, however for the skyline (as best I can tell) the lengths are about an inch off (2.5cm) on both sides. R33 my measure L 22" R 24.5" GPT L 22.5" 24.25" J30 L 23.5" 25.5"  so shaft length is probably an inch wider. Not sure if someone has another still remanufactured option besides the J30. I figured worst case I can buy a pair tear them down and swap the center shaft. My other option was reaching out to GSP to see if they cannot piece together a set, since the axle stubs are still manufactured, I wouldn't think it be that hard to find a shaft or make a shaft work. 
×
×
  • Create New...