Jump to content
SAU Community

Recommended Posts

I have a R32 GTR and the stock clutch is slipping very badly, so its time for me to change my clutch. I was told that 32 GTRs change from push to pull clutches half way through.. i was also told that it depends on which month the car was made and not which year. Is there somewhere on my car that i can check the date it was made? i can only seem to find the year it was made.. or can i somehow check if it is a push or pull clutch without taking it to the mechanics? thanks for any replies

Link to comment
https://www.sau.com.au/forums/topic/177857-1990-r32-push-or-pull-clutch/
Share on other sites

man that diagram is way off. no car has a solid line going all the way from pedal to slave. for starters the pedal actuates a ROD which goes into the MASTER. then a line (usually starting solid) goes down to near the slave, then a rubber hose goes the last little bit to the slave. NO GTR has a clutch cable. They are all hydraulic clutches.

Basically you need to stick your head under the drivers side of the clutch and take a look at which way the slave is going. ie is it pushing on the fork from the back, or from the front.

?

The operation of a push or pull clutch system outside of the bellhousing is identical. Compression of fluid at the master, pushes the slave cylinder out of its housing.

It is the direction of effort on the clutch fork that is the difference between push and pull.

Push, the slave cylinder is foreward of the clutch fork, pushes it backwards, inside the bellhousing the clutch fork PUSHES on the clutch to operate.

Pull, the slave cyinder is rearward of the clutch fork, pushes it foreward, inside the bellhousing the clutch fork (which is mechanically connected to the clutch ) PULLS the clutch assembly to operate.

Simplest way to check is: If the slave is foreward of the clutch fork, it is push, if it is rearward of the clutch fork, it is pull.

Zennon.. get rid of that confusing incorrect information.

Pull, the slave cyinder is rearward of the clutch fork, pushes it foreward, inside the bellhousing the clutch fork (which is mechanically connected to the clutch ) PULLS the clutch assembly to operate.

Simplest way to check is: If the slave is foreward of the clutch fork, it is push, if it is rearward of the clutch fork, it is pull.

nice to know somone agrees with me. :) and can explain it even better!

yes zennon I have no idea what cars you have been looking at mate, but no pedal is pulling on the master cylinder... and none have a pedal connected to the master cylinder by a cable. like I said above, the easiest way to tell is check which side your slave is on in relation to the clutch fork. :)

lol, there is no cable!! :)

ok, in a pull clutch the slave is on the other side of the clutch fork. but it still pushes on the fork, the fork is now doing pulling, instead of pushing. :( push clutch and pull clutch have completely different diaphragms. :)

im back ~ lol ok i sort of get the idea, just need a better picture or an explantion to zennons pic lol the pic kinda confuses me more hahaha damn >.< can u draw in clutch pedal in the pic too? so i can see where all this is relative to the pedal? and wat does the slave cylinder look like o_O real new at this, as u can tell lol =.="

Get on the ground and look at your gearbox, drivers side..

Should see something along the lines of this:

post-16250-1185365158_thumb.jpg

almost the same anyways.. generic pic.

red circle shows the slave cylinder. that is in front of the clutch fork pushing back, this is a push type clutch.

if your slave cylinder is in the yellow circle, pushing forward, it is a pull type clutch.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
×
×
  • Create New...