Jump to content
SAU Community

1990 R32, Push Or Pull Clutch?

Tomei_33
 Share

Recommended Posts

Tomei_33 Rising Star

Tomei_33

Posted
Posted

I have a R32 GTR and the stock clutch is slipping very badly, so its time for me to change my clutch. I was told that 32 GTRs change from push to pull clutches half way through.. i was also told that it depends on which month the car was made and not which year. Is there somewhere on my car that i can check the date it was made? i can only seem to find the year it was made.. or can i somehow check if it is a push or pull clutch without taking it to the mechanics? thanks for any replies

Link to comment
https://www.sau.com.au/forums/topic/177857-1990-r32-push-or-pull-clutch/
Share on other sites
Beer Baron Grand Master

Beer Baron

Posted
Posted

man that diagram is way off. no car has a solid line going all the way from pedal to slave. for starters the pedal actuates a ROD which goes into the MASTER. then a line (usually starting solid) goes down to near the slave, then a rubber hose goes the last little bit to the slave. NO GTR has a clutch cable. They are all hydraulic clutches.

Basically you need to stick your head under the drivers side of the clutch and take a look at which way the slave is going. ie is it pushing on the fork from the back, or from the front.

heller44 Mentor

heller44

Posted
Posted

?

The operation of a push or pull clutch system outside of the bellhousing is identical. Compression of fluid at the master, pushes the slave cylinder out of its housing.

It is the direction of effort on the clutch fork that is the difference between push and pull.

Push, the slave cylinder is foreward of the clutch fork, pushes it backwards, inside the bellhousing the clutch fork PUSHES on the clutch to operate.

Pull, the slave cyinder is rearward of the clutch fork, pushes it foreward, inside the bellhousing the clutch fork (which is mechanically connected to the clutch ) PULLS the clutch assembly to operate.

Simplest way to check is: If the slave is foreward of the clutch fork, it is push, if it is rearward of the clutch fork, it is pull.

Zennon.. get rid of that confusing incorrect information.

Beer Baron Grand Master

Beer Baron

Posted
Posted
Pull, the slave cyinder is rearward of the clutch fork, pushes it foreward, inside the bellhousing the clutch fork (which is mechanically connected to the clutch ) PULLS the clutch assembly to operate.

Simplest way to check is: If the slave is foreward of the clutch fork, it is push, if it is rearward of the clutch fork, it is pull.

nice to know somone agrees with me. :) and can explain it even better!

yes zennon I have no idea what cars you have been looking at mate, but no pedal is pulling on the master cylinder... and none have a pedal connected to the master cylinder by a cable. like I said above, the easiest way to tell is check which side your slave is on in relation to the clutch fork. :)

Beer Baron Grand Master

Beer Baron

Posted
Posted

lol, there is no cable!! :)

ok, in a pull clutch the slave is on the other side of the clutch fork. but it still pushes on the fork, the fork is now doing pulling, instead of pushing. :( push clutch and pull clutch have completely different diaphragms. :)

Tomei_33 Rising Star

Tomei_33

Posted
  • Author
Posted

im back ~ lol ok i sort of get the idea, just need a better picture or an explantion to zennons pic lol the pic kinda confuses me more hahaha damn >.< can u draw in clutch pedal in the pic too? so i can see where all this is relative to the pedal? and wat does the slave cylinder look like o_O real new at this, as u can tell lol =.="

heller44 Mentor

heller44

Posted
Posted

Get on the ground and look at your gearbox, drivers side..

Should see something along the lines of this:

post-16250-1185365158_thumb.jpg

almost the same anyways.. generic pic.

red circle shows the slave cylinder. that is in front of the clutch fork pushing back, this is a push type clutch.

if your slave cylinder is in the yellow circle, pushing forward, it is a pull type clutch.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...