Jump to content
SAU Community

Recommended Posts

what mph are you crossing the line at?

and was it 121hp or kw, cause i don't think you could do it with 123hp, even if you had drag slicks. if it was 121kw then i could believe it since i managed a 14.8 out of a magna with a 60ft time 0.187 slower than you. if i got a 2.0 60ft i'd be somewhere round the 14.5 mark.

i also notice that the dyno run you have posted says in the description that you say the car has a blocked cat, so if it does, what does it run without the blocked cat?

  • Replies 56
  • Created
  • Last Reply

Top Posters In This Topic

once again to clear things up, the car ran 123rwhp on the blocked cat, the 1/4 mile run was done with a new cat

No slicks were used, i explained what the car has done to it, nothing more nothing less.

If anyone lives in WA and wants to verify that it is what i say it is, then they are more than welcome to inspect the car.

Im not rogercordia, i dont have a need to make up bullshit

Im not rogercordia

rofl...

your brother may have set a new bench mark for NA times. i'll take it down the strip when i get a spare chance.

i make 115kw, which is roughly 150HP - we'll see how it compares.

i make 115kw, which is roughly 150HP

Have you got any mods? If so, what mods.

My RB25DE with only cat-back exhaust (probably makes no diff anyway) make 115kw aswell. No other mods, I am sure of that :whistling:

didn't dial any timing in. it's still whatever it is from the factory or previous owner.

the safc was to clean up the afr a bit not for any sort of power.

most of my mods are based around suspension parts and setup, not power.

although i might have to put some in to try this drag racing thing you guys call racing.

although i might have to put some in to try this drag racing thing you guys call racing.

hahahaha, i'm kinda the opposite, mostly been racing my cars down the strip but with the new gt-four im keen to throw it around a track, even if it does mean i'm just going around in circles....

Vote1 for Shaved head/thinner head gasket.

Increases CR a bit.

Most likely a few degrees extra dialled in on the CAS.

Check what timing it runs at idle, unsure on the GTS, but on the GTS-t it should be 15degrees.

Vote1 for Shaved head/thinner head gasket.

Increases CR a bit.

Most likely a few degrees extra dialled in on the CAS.

Check what timing it runs at idle, unsure on the GTS, but on the GTS-t it should be 15degrees.

It definately has timing smashed into it, i said that on the first page. From memory the cas is pretty much maxed out so its probably running around 25 degrees of timing at idle lol, which kinda throws the shaved head out the door cause with the extra CR and all that timing its would be pinging its nuts off all day long which isnt the case

Im getting my n/a tuned it already has a catback and coldair/pod. It is getting a piggyback system,cams and a lightened flywheel. When its all done ill scan the drag slip onto the computer :O

good stuff, post up what power you get after the tune aswell :D

anyone else has got a time to post up please do, i wanted to get some general comparision going to set a general bench mark for n/a owners but the thread kinda got sidetracked lol

there is the oppportunity if me might being able to do a 1/4 mle in november but i dont know if i want to cause my poor engine is tired and im ummmm'ing and rrr'ing about whether to do it or not..................

there is the oppportunity if me might being able to do a 1/4 mle in november but i dont know if i want to cause my poor engine is tired and im ummmm'ing and rrr'ing about whether to do it or not..................

just do it... lol

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I don't think the shuffle can damage the turbos. It only happens at low shaft speeds and loads. It's just annoying (to some people - others are tickled by the effect) and it quite possibly reduces spool performance a little bit.
    • Oh dear. The panel beating needs to be done before the filler work. Do you have a photo of the dent before you started? Hard enough to not flex and only hit the high spots?  What do you mean it was just temporary? 
    • Can u check this way it works for power supply?
    • These coils draw 10amps that what i read online
    • I appreciate the detailed explanation, think I understand now. I spent the better part of last night reading what I could about shuffle and potential solutions. I had replaced the OEM twin turbo pipe with an alternate Y pipe that is separated further away from the turbo. The current one is from HKS and I had a previous pipe that was separated even further away, both have shuffle. I had heard that a divider can be welded in to the OEM pipe to remove turbulence, and figure that aftermarket pipes that are more separated would achieve the same thing. From what I read, most people with -10 turbos get shuffle due to their size, though it's a bit less common with -5s on a standard RB26. I think Nismoid mentioned somewhere it's because OEM recirculation piping is common in Australia with -5 cars. It seems that the recommendation tends to vary between a few options, which I've ordered in what I think is most feasible for me:  1. Retune the MAP or boost controller to try to eliminate shuffle 2. Install OEM recirculation piping 3. Something called a 'balance pipe' welded onto the exhaust manifolds. I don't know if kits for this are available, seems like pure fabrication work 4. simply go single turbo My current layout is as follows: Garrett 2860 -5s HKS Racing Suction intake MAF delete pipes HKS racing chamber intake piping hard intercooler piping,  ARC intercooler HKS SSQV BOV and pipe Haltech 2500 elite ECU and boost solenoid/controller HPI dump pipes OEM exhaust manifolds HKS VCAM step 1 and supporting head modifications Built 2.6 bottom end All OEM recirculation piping was removed, relevant areas sealed off I'll keep an eye out for any alternative solutions but can get started with this.  Only other question is, does shuffle harm the turbo (or anything else)? It seems like some people say your turbo shafts will explode because of the opposing forces after a while and others say they just live with it and adjust their pedal foot accordingly. 
×
×
  • Create New...