Jump to content
SAU Community

Recommended Posts

what mph are you crossing the line at?

and was it 121hp or kw, cause i don't think you could do it with 123hp, even if you had drag slicks. if it was 121kw then i could believe it since i managed a 14.8 out of a magna with a 60ft time 0.187 slower than you. if i got a 2.0 60ft i'd be somewhere round the 14.5 mark.

i also notice that the dyno run you have posted says in the description that you say the car has a blocked cat, so if it does, what does it run without the blocked cat?

  • Replies 56
  • Created
  • Last Reply

Top Posters In This Topic

once again to clear things up, the car ran 123rwhp on the blocked cat, the 1/4 mile run was done with a new cat

No slicks were used, i explained what the car has done to it, nothing more nothing less.

If anyone lives in WA and wants to verify that it is what i say it is, then they are more than welcome to inspect the car.

Im not rogercordia, i dont have a need to make up bullshit

Im not rogercordia

rofl...

your brother may have set a new bench mark for NA times. i'll take it down the strip when i get a spare chance.

i make 115kw, which is roughly 150HP - we'll see how it compares.

i make 115kw, which is roughly 150HP

Have you got any mods? If so, what mods.

My RB25DE with only cat-back exhaust (probably makes no diff anyway) make 115kw aswell. No other mods, I am sure of that :whistling:

didn't dial any timing in. it's still whatever it is from the factory or previous owner.

the safc was to clean up the afr a bit not for any sort of power.

most of my mods are based around suspension parts and setup, not power.

although i might have to put some in to try this drag racing thing you guys call racing.

although i might have to put some in to try this drag racing thing you guys call racing.

hahahaha, i'm kinda the opposite, mostly been racing my cars down the strip but with the new gt-four im keen to throw it around a track, even if it does mean i'm just going around in circles....

Vote1 for Shaved head/thinner head gasket.

Increases CR a bit.

Most likely a few degrees extra dialled in on the CAS.

Check what timing it runs at idle, unsure on the GTS, but on the GTS-t it should be 15degrees.

Vote1 for Shaved head/thinner head gasket.

Increases CR a bit.

Most likely a few degrees extra dialled in on the CAS.

Check what timing it runs at idle, unsure on the GTS, but on the GTS-t it should be 15degrees.

It definately has timing smashed into it, i said that on the first page. From memory the cas is pretty much maxed out so its probably running around 25 degrees of timing at idle lol, which kinda throws the shaved head out the door cause with the extra CR and all that timing its would be pinging its nuts off all day long which isnt the case

Im getting my n/a tuned it already has a catback and coldair/pod. It is getting a piggyback system,cams and a lightened flywheel. When its all done ill scan the drag slip onto the computer :O

good stuff, post up what power you get after the tune aswell :D

anyone else has got a time to post up please do, i wanted to get some general comparision going to set a general bench mark for n/a owners but the thread kinda got sidetracked lol

there is the oppportunity if me might being able to do a 1/4 mle in november but i dont know if i want to cause my poor engine is tired and im ummmm'ing and rrr'ing about whether to do it or not..................

there is the oppportunity if me might being able to do a 1/4 mle in november but i dont know if i want to cause my poor engine is tired and im ummmm'ing and rrr'ing about whether to do it or not..................

just do it... lol

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Pads for R32 GTS-t, R32 GT-R non V-Spec (Sumitomo), R33 GTS-t and R34 GT-t are all interchangeable. R34 GT uses a 2x piston caliper, hence it didn't fit.
    • Checked with amayama and nope, the full S2 manual set is not available anymore. Unsurprising, but still disappointing as the ? on availability gave a glimmer of hope.
    • I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
×
×
  • Create New...