Jump to content
SAU Community

Urgent: Borrow Stock R33 Rims

Kaido_RR

By Kaido_RR,
in Western Australia

 Share

Recommended Posts

Onthehunt Veteran

Onthehunt

Posted
Posted
Legal i think is 1" up and 1" wider.

So stock is 16.6.5"

Legal Max would be 17x7.5"

Feel free to correct me if im wrong.

haha puts me in a bit of trouble. i thought it was 2" and 2"? anyone know for sure? i have been pulled over and cops said to me that I got pretty wide tyres on there but did not say about them being illegal.

bubba Grand Master

bubba

Posted
Posted

I believe the 1" out is referring to "track", you cannot change the TRACK of your vehicle more than 25mm either side. That said, if you want to go 2" wider you would need to get the correct offset so the TRACK doesn't change by more than 1" and hope you can clear it on the inside :D

342Four Grand Master

342Four

Posted
Posted

i think that you'll find that bubba is right

that, and the tyres cant actually protrude past the base print of the vehicle

so all my mates with those big muddies on their 4bees are actually illegal...

mitchy_ Grand Master

mitchy_

Posted
Posted

it used to be up to 7.5" in width, unless larger was a factory option.

and 2" increase in diameter as long as the rolling diameter didnt change.

now it is 1.3x the largest factory optioned rim width, providing the track doesnt increase by more than 25mm, and that it doesnt foul any part of the car.

and diameter can be anything that will allow for the same size rolling diameter.

also staggered sizes is still a big no-no, unless it came standard, but none of us drive porsches, so it doesnt matter!

ps. DPI is your friend, if in doubt ask them, rather than get 4574987504579437543750435 answers off the forums. :huh:

Guest

Guest

Posted
Posted

It is on a percentage ruling now from VSB 14 - National Code of Practice for Light Vehicle Construction and Modification (NCOP) with the link to DPI below, with V35's and 19's being an option you can go so big now and stay legal.

http://www.dpi.wa.gov.au/licensing/1421.asp

http://www.dotars.gov.au/roads/safety/bulletin/vsb_ncop.aspx

StuiE Rising Star

StuiE

Posted
Posted
it used to be up to 7.5" in width, unless larger was a factory option.

and 2" increase in diameter as long as the rolling diameter didnt change.

now it is 1.3x the largest factory optioned rim width, providing the track doesnt increase by more than 25mm, and that it doesnt foul any part of the car.

and diameter can be anything that will allow for the same size rolling diameter.

also staggered sizes is still a big no-no, unless it came standard, but none of us drive porsches, so it doesnt matter!

ps. DPI is your friend, if in doubt ask them, rather than get 4574987504579437543750435 answers off the forums. :)

I like the sound of that :whistling:

My Chaser has staggered sizes standard, as does Supras etc, so I can have (according to 1.3x) up to 9.5 wide, which is nice, since I have 9.5"s on the rear, had wondered on the legalitys of it :)

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R32 gtr transmission strength, billet plate

      By GTSBoy · Posted

      Just put skinny tyres on it.
    • cosline
      R32 gtr transmission strength, billet plate

      By cosline · Posted

      Yes, I know🙄 but the sequential is not in my budget... don't want to reduce power neither, so looks like I'm stuck in the rabbit hole🤣
    • Piggaz
      R32 gtr transmission strength, billet plate

      By Piggaz · Posted

      You’ll be very upset when you bust that too not to mention the gearing totally sucks. Don’t do it.
    • MBS206
      R32 GTS (RB20DE) Injectors Replacement

      By MBS206 · Posted

      Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • The Bogan
      NC MX5

      By The Bogan · Posted

      So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
×
×
  • Create New...