Jump to content
SAU Community

Recommended Posts

the time has come!

http://www.skylinesaustralia.com/forums/in...howtopic=183839

i cant believe im finally doing it

but i test drove a Audi S4 B5 2.7L twin turbo v6 today in yellow, black recaros inside leather ofcourse....

and im in love!

Ed

  • Replies 51
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

You will love the AUDI - they're tops cars :whistling:

Although they're a bit of a "wifes" car - good for her to do the shopping and get the kids from school then dad can give it a bit of punishment on the weekend

Was it like this one?

Imola_s4_avant.jpg

I tell ya what the GAYEST part of this whole thing is....

Starting the thread with...

the time has come!

FFS! can someone be a little bit more original :blink:

Oh.. and AUDI sucks.

Induction Twin Turbo intercooled

Power 195kW @ 5800rpm

Torque 400Nm @ 1850rpm-3600rpm

Acceleration 0-100Km/h 5.7 secs

Kerb Weight 1615kg

Chip it and get an extra 60 or so kw and alot more torque, then exhaust and intake and im flying!

Sorry mars! ill change it to

Id rather have a big debt and a newer car than an old skyline when i can afford to pay off a new car!??

AUDI%20S4%20F.jpg

buy a 180 ya fag

...and be like everyone else? :P

It's sad letting a car go, my current runabout goes on the market as soon as the Stagea lands from Japland.

As much as it has cost to keep it on the road and caused me a lot of problems i'm going to miss it. :google:

Best of luck with the Audi! :nyaanyaa:

servicing isnt too bad actually... its the parts that are a tad more expensive... but still not as bad as getting them overnight delivered from jaapaaaan

im over my imports at the moment, its twin turbo sleeper time!

A mate of mine who used to be on these forums went from a R33 gts-t to a 2.7l tt S4. Said the same stuff as you. Cat back exhaust set him back 5k and took 6 months to manufacture and send from the US. Getting someone local to chip it was a rort they wanted $1600 to load some software.

Things may have changed since then but i doubt its cheap yet.

Dont listen to them Ed! you will love the S4, i used to have a B6 1.8T Quattro work car and that was a very nice drive. Just remember with euro's you go through more brake discs compared to a jap car (usually every 2-3 sets of pads)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...