Jump to content
SAU Community

Recommended Posts

Hey

You can use an original WALBRO pump, they are about $160 delivered from SLIDE in the for sale trader section.

BOSCH 040 I believe is the one your chasing, that is also a good option.

Personally would go for an original WALBRO as they are very reliable pumps. Few people pushing 300rwkw with them, as well as being very easy to install!

Its been covered heaps on the forums. Check the DIY/tutorial section and you will find and installation guide more than likely, also search the forced induction section for like "what fuel pump" and you should get a lot of results.

Good luck.

Abu

Edited by abu

You can use either, the 040 has a filter built in and has to be mounted low, the 044 uses the standard sock filter and hose. If your r33 is stock you don't need either, if it's making 220rwkW - 280rwkW use the 040, if it's making 280rwkW - 400rwkW use 044.

Dont skimp on you fuel pump choice,go Nismo or Tomei,they are direct fit,and will easily cater to your power goal.

atm i'm making 180atw

but aimming for around 220-240

so i guess the walbro would be ok for this target?

cheers guys

yes it will be ok for that target but not much more

if your dead set you dont want no more than get the walbro/040 but MAKE SURE you dont want to go more because you will end up buying twice like alot of people

if i were to do it again, id spend the extra $250 and get a nismo/tomei from the start (ill have to do this when i change the turbo)

Dont skimp on you fuel pump choice,go Nismo or Tomei,they are direct fit,and will easily cater to your power goal.

TOMEI or a NISMO?

Man if you got the cash to spend $500 on a fuel pump then go ahead.. but a WALBRO pump for $160 delivered will serve you the EXACT same purpose.

There is a guy with an R33 which is running 300rwkw on a WALBRO pump.

http://www.skylinesaustralia.com/forums/in...=167572&hl=

Edited by abu

theres been alot of people that have had problems with walbros running lean as they get higher up

sure they should handle up to about 300kw but usually they dont

i have one and its fine but im only running 200kw..

anyhow its just what i have read from others exprience so dont take my word for it

there is a fuel pump control module (FPCM) which regulates between a low and high volume mode, other then that it just pumps either of the 2 modes, that being said in your engine bay is a fuel pressure regulator (FPR) which regulates the pressure of the flow into the fuel rail meaning that the pump just pumps at its one speed all the time and the FPR regulate it for you.

that why these guys are saying it doesn't matter which pump you go far, if the WALBRO is leaning out up top its because it pumping at maximum pressure / volume and simply cannot supply more fuel.

the FPR cannot up the pressure provided by the fuel pump merely reduce and regulate it

Would there be any problem with running a Tomei pump on a stock (with turbo back exhaust) R33 GTST. Would it run unnecessarily rich or does it only pump what is required?

You wont have any problem at all, it'll run fine (fuel reg will regulate pressure).

After much research and pondering what pump I should install (040, 044, Walbro 255, Tomei kit etc) I came to the conclusion that the Tomei kit (has everything you need including new seal, clamps, harness, wiring etc) is well worth the $360 advertised in the classifieds of this forum. It was a easy direct install with no modifications.

  • 8 months later...
I've just bought a new Walbro fuel pump from Slide, should be here on Monday.

I opted for the Walbro because I'm only aiming for around 200rwkw.

hey just wondering that walbro fuel pump that you got is that from the trading post

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
    • Yeah mate, never miss it.
    • Any going to watch World Time Attack at SMSP this year?
    • Appreciate the correction on the "ground", that will make a huge difference to looking at this. That makes complete sense about AF70/AF71 which is what I had come down to being the issue, one of these. I'll have another look in the ignition wiring when I get a chance next week. I'll also make up a jumper wire for running that AF73 test.  ECU is fine, relay itself is fine, pump harness is fine and the pump itself is fine. I am going to upgrade the Walbro 255 anyway with a DW300 I have since I need to replace the fuel sender and I'm going to upgrade the FPR with my chasebays kit ready for new plenum/injectors/dbw, but I'll get this working first. That's why this is so frustrating. 
×
×
  • Create New...