Jump to content
SAU Community

Recommended Posts

  • Replies 43
  • Created
  • Last Reply

Top Posters In This Topic

I think you'll find the story is that any parts on the car when it is shipped to Aus need to be destroyed before the car can be complied.

There is nothing in the import rules stopping you from modifying a car after you get it in Aus. This might be with parts that used to be on the car in jp.

If you were working in an industry that has just had a very deliberate crack down would you be sticking your neck out?

I can tell you this if you are unsure, ask your BROKER who is complying your car then ask who the workshop is and what will they do with the aftermarket parts and you want the answer in writing.

Or just deal with J-SPEC as Craig asked these questions a long time ago and has always told the truth and will show you the answer in writing.

Look guys read this simple as that dont believe anything unless it is writing.

14. Disposal of Non-Complying Parts

The workshop must have procedures and records to confirm that all non-complying parts removed from vehicles are either re-exported or destroyed. While the tyres on the imported vehicle still have to be replaced with new tyres, the tyres removed from the vehicle do not need to be destroyed. However, records need to be kept to show where the removed tyres have gone.

http://raws.dotars.gov.au/raws_online_guide.htm

Hmm. I e-mailed this to Geoff - he responded with:

We have spoken with the compliance workshops about this specifically and they have advised that despite being written into the RAWS guide there has been no confirmation of this from DOTARS themselves.  The workshops that are already operating are not destroying the parts, rather removing and replacing them with complying items.  If you would like to speak to one of them to feel safer, let me know and I'll supply contact details.

The car sits at the workshop until they gain their RAWS and if they dont get it the car is re-exported or destroyyed.

I know of people holding cars since January waiting to finish their RAWS.

I would be hesitant to let some people use my car as a test vehicle it would have to be somebody you had a lot of trust in.

  • 2 weeks later...

How would someone prove or disprove that parts were destroyed. Is the method for part destruction outlined somewhere?

All the workshop would have to do is keep a log book of parts removed and destroyed, and they are in the clear.

They can say the parts were crushed for scrap metal when really the parts were just given back to the original owner with no receipt or record.

This whole parts fiasco seems very stupid and pointless to me anyway. If the car is road worthy with the aftermarket parts on then what is the problem?

Originally posted by J-Spec Imports

EXACTLY - it is not going to be a cheap process, even with cheap original parts in Japan .. you will need to have "friend" over there that can do all of the running around for you..

Might I be of assistance?:P

I would destroy the parts, take photos of the parts and keep on hand a reciept from the scrap metal yard.

Or just dont bring in the cars with all the modified parts to make life easy.

I can tell you this if or when I have a RAWS I wouldnt bring in the car for somebody who says throw away $50,000 and your only income so some snot nose kid can save a couple of grand on a unroadworthy car that dosent pass ADR's.

It is as plane and simple as that, so I dont know why people are still complaining on this forum, like it will make a diference in DOTRS eyes.

Why not help people through the new rules not complain about them.

Driver, a modified car cannot be imported and complied under the new scheme.

The complier needs to provide proof the parts were destroyed.

The owner of the car would be responsible for the cost of replacing the parts. If you have bought via a broker, *you* are the owner.

Modified cars *can* be bought in if they are:

1) Older than 15 years old

2) Are a personal import that you have owned for more than 12 months overseas

3) For race or rally use only.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...