Jump to content
SAU Community

Recommended Posts

I snapped these images of my front and rear suspension. These were fitted before my R33 arrived from Japan.

FRONT

REAR

The rear says NISMO on the spring, but can't see it on front. These are coilovers right? I thought they are but i need a second opinion, and if someone knows anything about this model too.

Also can you tell if they are adjustable? The ride is very firm and bumps around a lot on uneven roads. It's great on smooth, high speed corners though. It's also been lowered a little.

Any advice is great. Cheers ;)

Link to comment
https://www.sau.com.au/forums/topic/184492-are-these-coilovers/
Share on other sites

Yes, all Skylines use coilover suspension from factory.

To see if they are adjustable, look for little knobs either at the bottom of the shock, or in your engine bay at the strut tops.

Edited by Yawn
yawn: skylines dont use coilovers from factory?

Yes, they do. A "coilover" is a suspension setup where the coil sits "over" (or, more accurately, around) the strut. Whether they're adjustable or not is irrelevant.

The V35 Skylines don't use a coilover arrangement in the rear, as the strut and spring are separated.

I'll jack up the car with the wheel off and take a looksy. I don't know what 'adjustable' looks like though, i'll take another pic?

I wanted to get my suspension adjusted anyways cause the ride is too firm for Sydney roads. Any advice on who to go see about that and relative costs?

sounds to me like you need your spring rates looked at.

or if you really want to be able to adjust your dampening and rebound then yes your going to have to go for a set of fully adjustable coil overs.

I'll jack up the car with the wheel off and take a looksy. I don't know what 'adjustable' looks like though, i'll take another pic?

I wanted to get my suspension adjusted anyways cause the ride is too firm for Sydney roads. Any advice on who to go see about that and relative costs?

If I remember the marketing guff correctly, they said that its to provide better geometry or something.

All I know is that I do get plenty of rear end grip in my Z33 (which shares the same platform), and its a right pain in the arse to adjust my ride height in the rear because you need to adjust the strut's mounting point as well as the cradle for the spring.

Not the spring rate (not likely). I would suspect the shocks are "dead". A nice set of Bilsteins, or even KYBs, would solve your ride problems.

I doubt they're dead. When there's people in the back the rear doesn't bounce around much. The ride is more comfortable and the shocks dampen bumps more. I want the suspension to absorb bumps all the time though! :)

drop your wheel and take some better pics of it. also check from the top of the strut if there's any notches etc where you can adjust the dampening.

nismo sells stiffer aftermarket springs to sit on stock struts too, so could just be stock struts with springs.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...