Jump to content
SAU Community

Recommended Posts

I have no aftermarket ECU management in my R33. I'm running 11-12psi on a stock turbo and the air/fuel mixture runs rich at these levels because the computer isn't programmed for these levels. I was told i need ECU mods (like fuel cut defender) but i wanted something with more adjustablity without going all-out on an expensive Power FC. I want something that will be good for a future mod plan up to 220rwkW.

Any suggestions???

Link to comment
https://www.sau.com.au/forums/topic/184965-ecu-upgrade/
Share on other sites

  • Replies 47
  • Created
  • Last Reply

Top Posters In This Topic

Did a search, SAFCII and Greddy E-Manage look very good, and similar.

Do either have any advantages over the other?

So i can do this piggyback tune to take my stock turbo up to 1 BAR and pump the correct amount of fuel in. That's how it works right?

Link to comment
https://www.sau.com.au/forums/topic/184965-ecu-upgrade/#findComment-3348646
Share on other sites

emanage with the injector and ignition harness is far better than te safc. but you do need the support tool or E01 to reap the benifits. SAFCII can be tunned from the unit but is only a afm signal bender. emanage does afm signal bending, injector duty cycle and ignition timing.

SAFCII is about 8 wires

emanage is about 30 wires (with all harnesses)

SAFCII can be picked up for about half the price of an emanage with all harnesses and support tool.

basicly the emanage is the next step up from a SAFCII

Link to comment
https://www.sau.com.au/forums/topic/184965-ecu-upgrade/#findComment-3348706
Share on other sites

Not sure what the harnesses are for the e-manage. But it sounds like a better long-term alternative.

What if i want two boost/power setting, like at 9psi for everyday, then flick a switch and jump to a 12psi remap???

Will the SAFCII & e-manage handle this? Cause i have a man. boost controller...will i need some kind of EBC upgrade, or an piggyback ECU & EBC all-in-one unit??? And can i reset the max. factory speed limit with a piggyback???

Edited by R338OY
Link to comment
https://www.sau.com.au/forums/topic/184965-ecu-upgrade/#findComment-3349627
Share on other sites

SAFCII can have two maps. just have to swap them over in the settings.

emanage you will have to have two maps saved on a laptop and plug the cable in a load the new one on to swap it over. (not a quick way)

manual boost controller will be ok, you'll just have to wind it up and check your gauges. EBC could be easier if you don't have to start mucking around with the gain settings and stuff.

i don't know that you can get a piggyback and EBC all in one. you can buy the greddy profec E01 (i think thats what its called) and use it with the emanage blue

and no, you cand remove factory speed cut with the SAFCII or emanage.

without getting the additional injector and ignition wiring harnesses for the emanage you might as well get the safcII.

also and most importantly make sure you know someone that can tune them.

Link to comment
https://www.sau.com.au/forums/topic/184965-ecu-upgrade/#findComment-3350279
Share on other sites

Maybe with all the messing around it mite be better just to fork out $1000+ for an FC...

I don't know much about em, but far as i know it replaces the stock ECU and it can control EVERYTHING the car does.

Do they stuff up? Should i go a 2nd hand one???

Link to comment
https://www.sau.com.au/forums/topic/184965-ecu-upgrade/#findComment-3351089
Share on other sites

Maybe with all the messing around it mite be better just to fork out $1000+ for an FC...

I don't know much about em, but far as i know it replaces the stock ECU and it can control EVERYTHING the car does.

Do they stuff up? Should i go a 2nd hand one???

if all your worried about is running rich im pretty sure i know how to fix it

ps how do you know its running rich

Link to comment
https://www.sau.com.au/forums/topic/184965-ecu-upgrade/#findComment-3351100
Share on other sites

Maybe with all the messing around it mite be better just to fork out $1000+ for an FC...

I don't know much about em, but far as i know it replaces the stock ECU and it can control EVERYTHING the car does.

Do they stuff up? Should i go a 2nd hand one???

I am selling my WOLF3d plug and play unit for a RB20/25.

Will plug straight into your loom, and can be tuned via hand controller.

Very similar to a PFC except it doesn't use a air flow meter, uses a MAP sensor.

Let me know if your keen, I will do you a good price. Cheaper than any PFC you will find for sale anyways.

Abu

Link to comment
https://www.sau.com.au/forums/topic/184965-ecu-upgrade/#findComment-3351152
Share on other sites

re-map :dry:

dude, whateva u do dont go for a power fc. that technology is old and outdated.

if u go the emanage ultimate, it can be continously updated, has more features than the pfc, and it looks like it is the new PFC.

the fact is the pfc is getting older and more expensive.=go the EMU

Link to comment
https://www.sau.com.au/forums/topic/184965-ecu-upgrade/#findComment-3358878
Share on other sites

Hi ,

Read this page http://www.skylinesaustralia.com/forums/in...howtopic=154016

I personally think youd have to be mad to buy a pfc for $1500 when you could have the ultimate for less that $900.

I believe the ultimate will eliminate your 180 kph limit, and has the option for a switch between 2 maps, ie race and street.

im about to get mine installed, so if u can wait a week or so ill post up some results then.

Link to comment
https://www.sau.com.au/forums/topic/184965-ecu-upgrade/#findComment-3359029
Share on other sites

Hi ,

Read this page http://www.skylinesaustralia.com/forums/in...howtopic=154016

I personally think youd have to be mad to buy a pfc for $1500 when you could have the ultimate for less that $900.

I believe the ultimate will eliminate your 180 kph limit, and has the option for a switch between 2 maps, ie race and street.

im about to get mine installed, so if u can wait a week or so ill post up some results then.

So about $900 new for the ultimate, and how much for installation and tune?

Thanks,

Abu

Link to comment
https://www.sau.com.au/forums/topic/184965-ecu-upgrade/#findComment-3359033
Share on other sites

So about $900 new for the ultimate, and how much for installation and tune?

Thanks,

Abu

I suppose that will determined by the workshop doing the install and tune. for the r33 being a plug and play, i cant see it costing more that $500 all up.

However this is only a guess.

I am getting my ultimate hard wired into my 34gtt (take longer than plug and play) and tuned,

plus tomei pump installed, plus injectors installed, fuel reg and z32 afm for around $1100.

Edited by silverr34gtt
Link to comment
https://www.sau.com.au/forums/topic/184965-ecu-upgrade/#findComment-3359055
Share on other sites

I suppose that will determined by the workshop doing the install and tune. for the r33 being a plug and play, i cant see it costing more that $500 all up.

However this is only a guess.

I am getting my ultimate hard wired into my 34gtt (take longer than plug and play) and tuned,

plus tomei pump installed, plus injectors installed, fuel reg and z32 afm for around $1100.

Oh yep fair enough.

Plug and play units seemed to still cost around the $500 mark for initial tune and installation (plugging it in..).

As far as I know they don't come programmed with a base map hey, so the tuner has to practically start from scratch?

Thanks for the info, I will do some research.

Edited by abu
Link to comment
https://www.sau.com.au/forums/topic/184965-ecu-upgrade/#findComment-3359067
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
×
×
  • Create New...