Jump to content
SAU Community

Recommended Posts

Noticed today that the latest Wheels magazine has a tyre test. Falken FK452 came a close second to some Goodyears I think. The tyres were 17's from memory, but it confirmed my theory that the Falken's were a great tyre for the money.

the winner was most likey the one who advertise's with them most!

  • 1 month later...
  • Replies 92
  • Created
  • Last Reply

Top Posters In This Topic

anybody recommend any places that sell tyres for cheap in Sydney?

Beaurepaires in Parramatta seems abnormally expensive! I got quoted (245/45/18) 450 a corner for dunlop sports max! and my bridgestone potenzas 520!?

doesnt seem right.

yeh mate that is a big ass rort

i got my Dunlop Sport Maxx 265/30/19 for $350 each

AGR Tyres in sefton. you REALLY need to haggle them downnnn

yeh mate that is a big ass rort

i got my Dunlop Sport Maxx 265/30/19 for $350 each

AGR Tyres in sefton. you REALLY need to haggle them downnnn

265/30/19 is a bit too small ? is that for the rear, or are you putting it on the front ?

best one not to throw your speedo off would either be 265/35r19 or 275/35r19

  • 1 year later...

Further to my comments above, while the Falken FK452's gripped well, they don't last very long. Lasted 20,000km on the rear, including one track day. Second hand Bridgestone RE40's that had already done 15000km, have lasted another 15000km, so they definately last longer, however, they are unbelievably noisy on the front. I got out to check that they hadn't been put on the wrong way, as they sounded like the All Terrain tyres on my wife's 4wd.

Would be interested to hear of any other Tyre reports now that you have had them on for a while?

anyone tried Bridgestone RE050A or the Adrenalin?

iam using adrenalin and both thumbs up for it!...and its much better in wet and cornering compare to what i had from the dealer - Dunlop some shxt...

FYI, Costco also selling it at a really good price for 17" and 18"s~

I've got Yokohama Advan sport V103 all round. Very high grip & low wear factor but pretty quite on tarmac. I selected them out of the available "performance" tyres due to reports of their low noise. The Michelin PS2 are without doubt the winner for low road noise but are also one of the most expensive, V103 cost me $2800 for all 4 & that's as low as I could get them. If I can afford to I'd get them again.

If not I'll look at some Nitto, Vredestein or Khumo.

I had KU31s on my car, they were fine, not the grippiest tyres but also not the worst. Treadwear was OK, had too much toe-out so killed the fronts fairly quickly. In my past experiences, from a grip perspective...

Bridgestone S03 > Hankook K107 > Hankook K110 > stock tyre > Kumho KU31 > Nankang NS2

Don't ever buy Nankang NS2...they were an experiment in tight-arsedness that won't ever be repeated again.

Yep, Nankang NS-II are horrible. I couldn't wait to get rid of the set that was on my car.

Ended up with kumho KU19s on the rear, $300 each for 275/30/20. Pretty good value, i think. No problems with the grip levels (for a street tyre) and they are a fair bit quieter than the nankangs. The only issue may be tyre wear but we'll see how it goes.

  • 3 months later...

Put my silvia rims onto the v35 which had Federal 595ss (235/40/18) and they're noisy as! Nonetheless, gripped well and lasted 30,000 so far and still just under 50% tread left. Will be changing tyres I think, because I don't think I can bare the 4wd noise much longer (never realised how noisy they were in the silva!!!)...

Will go for the taller 45 tyre, but just deciding on a quiet, hard wearing tyre...

My import arrived with Yoko Decibels. Tread was down and I wanted top replace them, but with what? Did some research and spoke to some tyre places. The Yoko was quiet (hence the name) but Expensive! Ended up running with the Toyo T1R. Not quite as expensive, quiet and holds to the road well. Done 2,000Klm on them now and very happy.

For what it's worth at this late point in the thread.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Stock ECU (or more accurately stock tune) absolutely refuses to go over 10psi and behaves like you have seen. The Nistune is the same if it is the stock tune. If the Nistune chip has been tuned, the resulting tune could be literally anything for any combination of parts. The Nistune just makes the stock ECU Tunable.
    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
×
×
  • Create New...