Jump to content
SAU Community

Recommended Posts

i use the sougi, its a 10w40 im pretty sure..

he has the 32R brakes. you will need an adaptor sleeve to fit these. but he is upgrading to the 34R brembos soon, which bolt straight on to the fronts. so far the only bolt on for the rear i know about is the 350z brembos.

Thanks for clearing that up Scotty it all makes sense now. :rolleyes:

Do you think that nissans 7-30w oil is good choice, whats everyone else using?

I know 300v is best which I use in gtr but 90 for 4 lt is a bit rough for frequent oil change.

nissan is 55 bucks for 5 lt.

Cheers

Dave

300v will last you 10,000kms before you need to change it (just get a good filter).

Nissan's oil is a mineral base. Unsatisfactory in this day and age IMO.

300v will last you 10,000kms before you need to change it (just get a good filter).

Nissan's oil is a mineral base. Unsatisfactory in this day and age IMO.

you can get Greddy filters from Autobarn at about $20 i think

Synthetic filter with a Magnet.

saves gettin em online through ebay etc..

you can get Greddy filters from Autobarn at about $20 i think

Synthetic filter with a Magnet.

saves gettin em online through ebay etc..

That's not bad! I used a Ryco Z445 for my last oil change and that was $18 from SuperCrap...

Will be getting the Greddy from now...

yeh they are the same size as stock aswell. especially if your doing 10,000k changes, they will definitely last the extra 5k.

if your doing 5000k changes, ryco is fine. jus whack a magnet on it lol. it works suprisingly

yeh they are the same size as stock aswell. especially if your doing 10,000k changes, they will definitely last the extra 5k.

if your doing 5000k changes, ryco is fine. jus whack a magnet on it lol. it works suprisingly

lol... I don't think it is the same thing mate, you need to take into account the flow pattern of the filter so sticking a magnet "anywhere" is not that great an idea IMO

The reason the PE/HKS/Greddy magnets are the size/shape and positioned where they are is so the oil flows over and around the magnet with as little disruption as possible and without the chance of clogging up one area of the filter.

lol... I don't think it is the same thing mate, you need to take into account the flow pattern of the filter so sticking a magnet "anywhere" is not that great an idea IMO

The reason the PE/HKS/Greddy magnets are the size/shape and positioned where they are is so the oil flows over and around the magnet with as little disruption as possible and without the chance of clogging up one area of the filter.

:teehee:

yeh lol so a magnet right on the end of the filter

it used to work on the integra.. didnt clog anything. theyre magnets actually designed to go out the end of the filter.. comes with like 10 of em incase you lose one driving around haha

i wouldnt do it anymore. but hearing abit of metal(the magnet) hit the floor would scare the shit out of me.. lol

lol... not to worry, just pay a king's ransom for some 300v and run it for 10,000kms.

interesting fact: I got hold of the GW 'oil engineers' and was told that the SynX stuff is ethanol tolerant. you wont notice more that a 1kw difference, only downside is sougi 10,000k changes, and synx will need 5,000k.

fact that its mineral/synthetic mixture is abit of a ehhh, but at 5,000k changes wouldnt cause problems right?

interesting fact: I got hold of the GW 'oil engineers' and was told that the SynX stuff is ethanol tolerant. you wont notice more that a 1kw difference, only downside is sougi 10,000k changes, and synx will need 5,000k.

fact that its mineral/synthetic mixture is abit of a ehhh, but at 5,000k changes wouldnt cause problems right?

You should be okay with a semi for 5000kms.... BUT considering the power level and previous issues with turbo failure, why would you skimp on the life blood of your engine?

Oh, and oil is not there to extract power from your engine, it is there to lubricate and clean.

Whom have you been talking to that measure how good an oil is by the kw +/-???

Edited by iamhe77

You should be okay with a semi for 5000kms.... BUT considering the power level and previous issues with turbo failure, why would you skimp on the life blood of your engine?

Oh, and oil is not there to extract power from your engine, it is there to lubricate and clean.

Whom have you been talking to that measure how good an oil is by the kw +/-???

no i meant as in maybe 1kw less.. as its quality isnt up there with sougi..

im not using it, just voicing what i was told. im really dreading the day i have to go back to buying $120 worth of 300v, or whatever the rediculously stupid price is.

interesting fact: I got hold of the GW 'oil engineers' and was told that the SynX stuff is ethanol tolerant. you wont notice more that a 1kw difference, only downside is sougi 10,000k changes, and synx will need 5,000k.

fact that its mineral/synthetic mixture is abit of a ehhh, but at 5,000k changes wouldnt cause problems right?

Yeah, well the GW "oil engineer" recommended a 20w50 mineral oil for my 170hp GSXR1000; rolleyes.gif

Worst. Oil. EVER.

I argued the toss with him, as I was face to face in their head office in Penrith, and he assured me HEAPS of other GSXR owners were using it, and loved it.

Well either they, or him are stupid wankers. Bike wouldn't idle, wouldn't rev out; felt about 30hp down.

Threw that shit away, never again.

Silkolene 10w40 full synth; back to normal. Bad advice; shit oil.

Edited by Daleo

Yeah, well the GW "oil engineer" recommended a 20w50 mineral oil for my 170hp GSXR1000; rolleyes.gif

Worst. Oil. EVER.

I argued the toss with him, as I was face to face in their head office in Penrith, and he assured me HEAPS of other GSXR owners were using it, and loved it.

Well either they, or him are stupid wankers. Bike wouldn't rev out; felt about 30hp down.

Threw that shit away, never again.

oh.

well not using that then lol

oh.

well not using that then lol

Same guy recommended a 20w50 mineral for my Stagea; actively tried to steer me away from Sougi, even after I specifically asked for it.

Tried to feed me all manner of bunkum about how a mineral was WAAAY better for my situation than a Semi or even Full Synth. Explained the engine, and the fact it was turboed, told him that cost wasn't an issue but he still pushed it.

I asked if he was a salesman, but he assured me he was one of their engineering staff.

Edited by Daleo

Same guy recommended a 20w50 mineral for my Stagea; actively tried to steer me away from Sougi, even after I specifically asked for it.

Tried to feed me all manner of bunkum about how a mineral was WAAAY better for my situation than a Semi or even Full Synth. Explained the engine, and the fact it was turboed, told him that cost wasn't an issue but he still pushed it.

I asked if he was a salesman, but he assured me he was one of their engineering staff.

maybe they got theyre engineers degree, by engineering their way through the maze on the back of a coco pops box lol

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...