Jump to content
SAU Community

Recommended Posts

Hi guys,

I washed my rear seats (coupe r33) (dont ask) and in the bath tub and now they are really moist inside, its a pain to dry them out... my brother said to take it to panel beaters and put the seats into the oven they have... is this a good idea or any oher way to dry them out?

I was offered to buy second hair s2 rear seats for 100 bucks +freight. what would you guys do?

cheers

Edited by Modena
Link to comment
https://www.sau.com.au/forums/topic/187088-wet-seats-need-help-quick/
Share on other sites

I would just use a hair dryer or just leave them out in the sun depending on how the weathers like. Not sure if I'll go out and buy a new set just yet. How long has it been since you gave them a bath?

hairdryer and lotsa towels

towels actually absorb water (their moleculer make-up is such that they 'suck up' water - not just hold water in-between the fibres)

so bung lotsa towels all over it and let them try to soak up some water, then hit it with the hairdryer for a long time

the real question is why did you wash your car seats in the bathtub. and what kind of stains were you trying to remove. jb.gif

Cat pee, the box where I had my cat tipped on the side and the pee trickled onto the seat... bad smell... tried many things to get it out, didnt work, until I got carried away with baking soda... that removed the smell but the baking soda has truelly left its mark on the seats... Hence why they needed a wash.

Yeah get a room as hot as you can and leave it in there. You can even buy one of those moisture trap things, like a little plastic bucket filled with silica crystals that you buy at Woolies or whatever and leave that under the seat while it dries to draw out moisture.

But damn, cat pee, for 100 bucks id just buy the new seats instead of having a faint odour return on warm days :ninja:

any osmosis or capillary action is going to take forever to dry the seats. you're better off pointing a heater at them and squeezing the seat every few minutes. that should at least push some of the water to the outer layers where the heater can dry it, then squeeze again and repeat.

it's going to take a long time to dry the seats out completely though.

Did you end up getting the smell out in the end? Or did you just purchase new seats because you got sick of waiting? $65 is cheap.

The smell is out although one part of the seats smells rather damp... dont know if it will come out in time.

I got the replacement seats because to me it seemed too long to wait and I dont want to risk missing out on cheap S2 seats... there are many S1 seats but not that many s2s...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
    • I forgot about my shiny new plates!
    • Well, apparently they do fit, however this wont be a problem if not because the car will be stationary while i do the suspension work. I was just going to use the 16's to roll the old girl around if I needed to. I just need to get the E90 back on the road first. Yes! I'm a believer! 🙌 So, I contacted them because the site kinda sucks and I was really confused about what I'd need. They put together a package for me and because I was spraying all the seat surfaces and not doing spot fixes I decided not to send them a headrest to colour match, I just used their colour on file (and it was spot on).  I got some heavy duty cleaner, 1L of colour, a small bottle of dye hardener and a small bottle of the dye top coat. I also got a spray gun as I needed a larger nozzle than the gun I had and it was only $40 extra. From memory the total was ~$450 ish. Its not cheap but the result is awesome. They did add repair bits and pieces to the quote originally and the cost came down significantly when I said I didn't need any repair products. I did it over a weekend. The only issues I had were my own; I forgot to mix the hardener into the dye two coats but I had enough dye for 2 more coats with the hardener. I also just used up all the dye because why not and i rushed the last coat which gave me some runs. Thankfully the runs are under the headrests. The gun pattern wasn't great, very round and would have been better if it was a line. It made it a little tricky to get consistent coverage and I think having done the extra coats probably helped conceal any coverage issues. I contacted them again a few months later so I could get our X5 done (who the f**k thought white leather was a good idea for a family car?!) and they said they had some training to do in Sydney and I could get a reduced rate on the leather fix in the X5 if I let them demo their product on our car. So I agreed. When I took Bec in the E39 to pick it up, I showed them the job I'd done in my car and they were all (students included) really impressed. Note that they said the runs I created could be fixed easily at the time with a brush or an air compressor gun. So, now with the two cars done I can absolutely recommend Colourlock.  I'll take pics of both interiors and create a new thread.
×
×
  • Create New...