Jump to content
SAU Community

Recommended Posts

ok when im idling and i turn on my air con, the car revs up to 1500rpm, then drops to 700rpm like it does that quick goes up and down up and down until i turn it off or wait until it settles down, which it does after a while, also its only blowing hot air now (could need a re-gas, but that was done only just a year ago how come its gone so quick), and sometimes when i press mode to skip through where i want air blowing it makes a clicking sound loud and for atleast 30 seconds, heater works good though, although last time i used my a/c was back in april lol and thats when every time i used the a/c the gears were hard to get into, especially 1 and reverse LOL

someone help ^_^ stupid climate control

Link to comment
https://www.sau.com.au/forums/topic/187370-air-con-disease/
Share on other sites

ok when im idling and i turn on my air con, the car revs up to 1500rpm, then drops to 700rpm like it does that quick goes up and down up and down until i turn it off or wait until it settles down, which it does after a while, also its only blowing hot air now (could need a re-gas, but that was done only just a year ago how come its gone so quick), and sometimes when i press mode to skip through where i want air blowing it makes a clicking sound loud and for atleast 30 seconds, heater works good though, although last time i used my a/c was back in april lol and thats when every time i used the a/c the gears were hard to get into, especially 1 and reverse LOL

someone help ^_^ stupid climate control

There is a diagnostic check that you can run to tell what the problem is.....

Start car and hold down the OFF button for 5 seconds and it will go into diagnostics mode.....

It will then show you any error codes.

Link to comment
https://www.sau.com.au/forums/topic/187370-air-con-disease/#findComment-3382107
Share on other sites

Probably just coincidence that the gear selection is awkward when A/C on.

The ECU will raise the idle revs when it gets the signal that the A/C is operating. The hunting for idle is probably the AAC valve.

Try holding the "cold" button until the unit displays "FC" (full cold) - does it still blow hot?

Link to comment
https://www.sau.com.au/forums/topic/187370-air-con-disease/#findComment-3382290
Share on other sites

There is a diagnostic check that you can run to tell what the problem is.....

Start car and hold down the OFF button for 5 seconds and it will go into diagnostics mode.....

It will then show you any error codes.

What's it mean if all the lights light up. all good or all bad.

BTW where do you find all these diagnostic tests?

Link to comment
https://www.sau.com.au/forums/topic/187370-air-con-disease/#findComment-3382719
Share on other sites

Probably just coincidence that the gear selection is awkward when A/C on.

The ECU will raise the idle revs when it gets the signal that the A/C is operating. The hunting for idle is probably the AAC valve.

Try holding the "cold" buton until the unit displays "FC" (full cold) - does it still blow hot?

so i started the car and held the off button but nothing happened LOL wtf!! cold button? the blue one? its down to 18c but still hot as, sux coz its getting real hot nowadays + i cant believe it needs a regas so quick!!

Link to comment
https://www.sau.com.au/forums/topic/187370-air-con-disease/#findComment-3383432
Share on other sites

so i started the car and held the off button but nothing happened LOL wtf!! cold button? the blue one? its down to 18c but still hot as, sux coz its getting real hot nowadays + i cant believe it needs a regas so quick!!

It could be a leak in your system or you've got a stuffed motor (motor which controls the hot/cold). First thing is try the diagnosis to see what's going on before ripping out your dash.

Link to comment
https://www.sau.com.au/forums/topic/187370-air-con-disease/#findComment-3384251
Share on other sites

it doesnt want to go into diagnostic mode? :S the clicking isnt normal, as it never happened until recently :) damn ripping out the dash.....oh well perfect time to install some gauges etc etc, i'll try a regas 1st then see what happens, if theres a leak in the system how do i go about fixing that, can it be a diy? or needs to be done professionally

Link to comment
https://www.sau.com.au/forums/topic/187370-air-con-disease/#findComment-3386433
Share on other sites

it doesnt want to go into diagnostic mode? :S the clicking isnt normal, as it never happened until recently :D damn ripping out the dash.....oh well perfect time to install some gauges etc etc, i'll try a regas 1st then see what happens, if theres a leak in the system how do i go about fixing that, can it be a diy? or needs to be done professionally

If the car is more than 5 years old the rubber hoses were made to handle R12 refrigerant - the cocktail of gas used now is molecularly smaller and will weep through the pores in the hose - common thing - if you re-gas it will slowly deplete again, only way out is to try and get some R12 - but i doubt if you will. The hoses have to be replaced.The reason it is hunting is because oh the LP switch sensing a drop in pressure and the compressor clutch is comming in and out. sorry

:)

Link to comment
https://www.sau.com.au/forums/topic/187370-air-con-disease/#findComment-3386559
Share on other sites

it doesnt want to go into diagnostic mode? :S the clicking isnt normal, as it never happened until recently ;) damn ripping out the dash.....oh well perfect time to install some gauges etc etc, i'll try a regas 1st then see what happens, if theres a leak in the system how do i go about fixing that, can it be a diy? or needs to be done professionally

The clicking noise is worn out gears. The gears which move your vent direction is worn out and the motor slips while trying to turn it.

Link to comment
https://www.sau.com.au/forums/topic/187370-air-con-disease/#findComment-3387219
Share on other sites

yeah same, stupid aircon fan, errm expensive to replace these gears? motor or whatever? how about the hoses? its too bloody hot :) dont even feel like smoking coz its so hot, how about the problem with my gearbox? like it only happens when i turn the aircon on (cold) on heater its fine, once i couldnt get into any gears it would crunch even when i was at a stand still, but if i gave it a rest and came back few hours later would be fine, hence the reason i havent used my aircon for ages lol, try parking without being able to get into gear :P

Link to comment
https://www.sau.com.au/forums/topic/187370-air-con-disease/#findComment-3388401
Share on other sites

That idle up then down is the clutch engaging the aircon compressor, which increases the load on the engine, and the AAC valve increases your idle to compensate so it doesnt stall. The drop down occurs when your thermostat is at the correct temperature and the clutch is disengaged from the compressor. Perfectly normal unless the Aircon switches aint working. The clicking sounds can also be the vents opening and closing, its a common problem apparently, the little plastic teeth come off the rails so im told??? but requires the whole dash to come apart - stuff that

I dont think the size of the molecule matters witht the aircon hose, I think its more the press fittings which are the issue, or any threaded joints especially if youve been moving/bending aircon pipes/hoses about the place to get your FMIC to fit. Take it to an aircon place, they inject a die into the cooling system to check for leaks, make sure you tell them o/wise theyll just fill it up and send you on your way - they love it, cos you come back in six months to get the same thing done. O/wise keep the windows down and make sure your heaters turned up - problem solved :D

Link to comment
https://www.sau.com.au/forums/topic/187370-air-con-disease/#findComment-3392553
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You won't need to do that if your happy to learn to tune it yourself. You 100% do not need to do that. It is not part of the learning process. It's not like driving on track and 'finding the limit by stepping over the limit'. You should not ever accidently blow up an engine and you should have setup the ECU's engine protection to save you from yourself while you are learning anyway. Plenty of us have tuned their own cars, myself included. We still come here for advice/guidance/new ideas etc.  What have you been doing so far to learn how to tune?
    • Put the ECU's MAP line in your mouth. Blow as hard as you can. You should be able to see about 10 kPa, maybe 15 kPa positive pressure. Suck on it. You should be able to generate a decent vacuum to about the same level also. Note that this is only ~2 psi either way. If the MAP is reading -5 psi all the time, ignition on, engine running or not, driving around or not, then it is severely f**ked. Also, you SHOULD NOT BE DRIVING IT WITHOUT A LOAD REFERENCE. You will break the engine. Badly.
    • Could be correct. Meter might be that far out. Compare against a known 5 ohm 1% resistor.
    • @Murray_Calavera  If I were an expert I wouldn't be in here looking for assistance.  I am extremely computer literate, have above average understanding on how things should be working and how they should tie together.  If I need to go to a professional tuner so be it, but I'd much rather learn and do things myself even if it means looking for some guidance along the way and blowing up a few engines. @GTSBoy  I was hoping it would be as simple as a large vacuum leak somewhere but I'm unable to find anything, all lines seem to be well capped or going where they need to be, and when removed there is vacuum felt on the tube.  It would be odd for the Haltech built in MAP to be faulty, the GTT tune I imported had it enabled from the start, I incorrectly assumed it was reading a signal from the stock MAP, but that doesn't exist.  After running a vacuum hose to the ECU the signal doesn't change more than 0.2 in either direction.   I'll probably upload a video of my settings tomorrow, as it stands I'm able to daily drive, but getting stuttering when giving it gas from idle, so pulling away from lights is a slow process of revving it up and feathering the clutch until its moving, then it will accelerate fine.  It sounds like I need to get to the bottom of the manifold pressure issue, but the ignition timing section is most intimidating to me and will probably let a pro do that part.  Tomorrow I'll try a different vacuum line to T off of, with any luck I selected one that was already bypassed during the DBW swap.  (edit: I went out and did it right now, the line I had chosen did appear to have no vacuum on it, it used to go to the front of the intake, I've now completely blocked that one off at the bracket that holds several vacuum lines by the firewall.  I T'd into the vacuum line that goes from that bracket to the vacuum pump at the front of the car, but no change in the MAP readings).  Using the new vacuum line that has obvious vacuum on the hose, im still only getting readings between -6.0 and -5.2.  I'm wondering why the ECU was detecting -5.3 when nothing was connected to the MAP nipple and ECU MAP selected as the source. @feartherb26  I do have +T in the works but wanted to wait until Spring to start with that swap since this is my good winter AWD vehicle.  When removing the butterfly, did it leave a bunch of holes in the manifold that you needed to plug?  I thought about removing it but assumed it would be a mess.   I notice no difference when capping the vacuum line to it or letting it do its thing.  This whole thing has convinced me to just get a forward facing manifold when the time comes though.
    • Update: tested my spark plugs that are supposed to be 5ohms with a 10% deviation and one gave me a 0 ohms reading and the rest were 3.9ohm<, so one bad and the others on their way out.
×
×
  • Create New...