Jump to content
SAU Community

Recommended Posts

I haven't taken my car to the track yet and i am just woundering what pads i should use.

i would just be putting them in driving to the track going for a run and taking the pads out again once i got home.

I have a solid (vented)front rotor and drilled rears. I will get slotted rotters for the car in time but untill then i will stay with the setup the last owner had.

Its a r32 GTR.

Also after the best tyres for the track and where to get them?

and can you run semi slicks on just the wakefield licence.

Cheers

Keith

Edited by BNR32t
Link to comment
https://www.sau.com.au/forums/topic/188200-brake-pads-for-the-track/
Share on other sites

I haven't taken my car to the track yet and i am just woundering what pads i should use.

i would just be putting them in driving to the track going for a run and taking the pads out again once i got home.

I have a solid (vented)front rotor and drilled rears. I will get slotted rotters for the car in time but untill then i will stay with the setup the last owner had.

Its a r32 GTR.

Also after the best tyres for the track and where to get them?

and can you run semi slicks on just the wakefield licence.

Cheers

Keith

I will probably be going for the EBC red's for everyday use and track (designd for the track as they need to heat up to be most effective). Are you looking at changing the rotors as well? You normally let the pads bed in to the rotors and swapping and changing them would seem to limit their effectiveness.

I'm still considering tyres, Ladybytes swears by here Federal 595 RS's.

The wakefield licence allows you to run full slicks if you want.

I will probably be going for the EBC red's for everyday use and track (designd for the track as they need to heat up to be most effective). Are you looking at changing the rotors as well? You normally let the pads bed in to the rotors and swapping and changing them would seem to limit their effectiveness.

I just had these installed last week along with some new RDA rotors. You're sure as hell right in that they need to be warmed up to be at their best.

I've got EBC reds. Yep you need to dig into them a bit when not really warm to stop fast. I'm very happy with their stopping power in general in combination with my RDA front slotted rotors and about to try them on the track. They are half worn already, so we'll see :( My mechanic says the EBC Greens are even more track oriented and need to be warmed up even more!

Edited by sl33py
My mechanic says the EBC Greens are even more track oriented and need to be warmed up even more!

Your mechanic is wrong then :( the greens are a "performance" steet pad. the EBC Red's are more of a "high performance" street/Track. I ran RB74's on wakefield and although some people say they are not as good as some other brands when you way up the $$$ vs performance i thought they did bloody well, no break fade or anything like that

I just had these installed last week along with some new RDA rotors. You're sure as hell right in that they need to be warmed up to be at their best.

They still break as well as ordinary pads when cold? Just lots better when warm?

It normally takes 500km to get the pads and the rotors to bond most effectively. Hopefully it will improve over time?

It normally takes 500km to get the pads and the rotors to bond most effectively. Hopefully it will improve over time?

Yeah hopefully they eventually stop squealing loud enough to wake the dead after 500kms!

What are the ferodo's like everyday?

Or are they just a track pad?

im still using them on my car and they've been on the car for a year and a half! (done 3 full track days on them). they are great on the street. they take about 2-3 normal braking applications to warm up and work effectively, but once you've done that, they're perfect. as an everyday pad, i would recommend them.

as for the track, they are also great. they can handle big temps and wont fade (in my experience anyway). i warped my brake discs before my brakes faded, then my fluid boiled, but the pads stayed true and still to this day will stop my car on a dime....

will is ds2500 the part number? Will they go straite into my r32 standard rotors? Or will i need a different part number?

Cheers Frink, Cause i work at repco and we sell ferodo's so it might be a cheap option for me.

thanks heaps mate.

For Brakes I would go for Bendix Ultimate, they're great for everyday driving, takes about 2 good stops for them to get good "bite", I used them at Texikhana recently and had no fade, sqeal, grinding or excess heat... They were great.

For tyres - street legal semi slicks go for Federal 595RS, best bang for your buck tyre available.

will is ds2500 the part number? Will they go straite into my r32 standard rotors? Or will i need a different part number?

Cheers Frink, Cause i work at repco and we sell ferodo's so it might be a cheap option for me.

thanks heaps mate.

they should do straight in the rotor, they do for 33's. you should be able to research the part number in the cataloge you should have behind the desk (im only guessing...). they are more expensive then the Bendix Ultimates, but i think its worth it....

its funny, just as i say all these good things about these pads, only this morning they ran out pad and i now need new ones! oh well, they're still a great pad....

I'm now considering EBC yellows, better in all ways to the reds except for dust. Not so sure on the quietness though, they don't advertise that.

Considering I can land a full set (F+R) for the GTR for $330, that is a huge saving.

you will find the EBC yellows are more of a track pad than the reds, if its for everyday street use even EBC recommend against going the yellows over the reds.

edit: makes more sense now.

Edited by TiTAN

EBC says:

Ultra high friction pads for race use but perfectly safe for street use (Formula 1846).

Although a full race material and capable of high temperature use with very good wear life, this new formulation sets a new trend in race type brake pad compounds that can be used on the highway. The “bite” from cold is superb which is uncommon with race materials (normally requiring warm-up) and makes this a pad which can be safely used on both street and track. This new formulation has been used by numerous championship race and rally drivers and is truly a milestone in brake pad material development. Nominal friction coefficient 0.5 with zero rotor damage and similar dust to original pads.

http://www.ebcbrakes.com/yellowstuffinfo.html

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
    • Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
    • Can you clarify what you mean by boost cut, do you mean it misfires both when under load (driving) and when stationary and out of gear? Or does the ECU pull power when it reaches a specific boost level that is too high (boost control issue)? Does it occur at idle with no throttle? When you say "the ECU is OK", what ECU is it and why do you think it is OK? Have you used the NEO ECU, and if so do you have a MAP sensor attached? Same for the AFM, why do you think it is OK? Do you have any way to put a fuel pressure gauge on it (even just a mechanical one between the fuel filter and fuel rail)?
×
×
  • Create New...