Jump to content
SAU Community

Recommended Posts

IMHO with you running that sort of power I'd go an OS replacement gear set...with the initial parts cost plus fitting it won't be too much more than trying to find a GOOD s/h series 3 box.

If moneys is short just replace with a good 2nd hand series 1/2 box....

If money is not short, how much should i be looking to spend on a gearset?

I just found a series 3 box for $1,100+ freight which i thought to be pretty reasonable but i dont want to keep doing this over and over. The previous owner killed two boxes before me and strangley enough they have all been in 3rd gear. I am sure my triple plate clutch is not helping the cause.

Edited by fieds83

Transfer case isn't worth that much... you can swap yours onto it.

The power your running isn't killing the boxes, it's either the clutch or your driving style or both. Chances are it's the clutch killing the boxes. You could put a OS Giken gearset through your S3 box, probably cost you between 3-5k.....

Yeh, just checked greenline and they have 5 speed cross mission gearsets on sale for $2,480aud. So i would be expecting $3,500-$4,000 fitted.

Thanks for the info, the clutch is copping most of the blame in this instance though i have to admit it happened in the heat of the moment.

yeah, i had 300awkw for 18 months no dramas. re-tuned to 376 and smashed 2 of them within a month. got a ppg now. so ya a os gearset is the go. and since yours is a s3 you dont need to get the upgrade parts from nissan.

it will be cheaper in the long run. they are about 2.5k for the set. with the input shaft.

yeah. i have run a os twin, nismo twin, both damperd. nismo tripple and a r3c os. all without issue untill the power rose. my frst one(route6 ) stripped the input shaft gear.when changing to 3rd. and the second standard gearbox smashed all the teeth of 3rd after ONE QUICK change.

yeah. i have run a os twin, nismo twin, both damperd. nismo tripple and a r3c os. all without issue untill the power rose. my frst one(route6 ) stripped the input shaft gear.when changing to 3rd. and the second standard gearbox smashed all the teeth of 3rd after ONE QUICK change.

yeah. i have run a os twin, nismo twin, both damperd. nismo tripple and a r3c os. all without issue untill the power rose. my frst one(route6 ) stripped the input shaft gear.when changing to 3rd. and the second standard gearbox smashed all the teeth of 3rd after ONE QUICK change.

I think you would be doing pretty well to get a good series 3 box for 1100. The trouble with 2nd hand boxes is that unless you can open it up and look before you buy you are never sure what you are getting.

For the power you have listed and you have $3ish k to spend without doubt go an aftermarket gearset like an OS....I've seen way too many std boxes in GTR's break with that power (granted it was track use). If you don't have the money then try an find a good condition 2nd hand R33 box and as long as you don't have a solid center clutch and are fairly gentle with it it should last a while.

All I know is that the series 3 boxes have stronger syncros and a few other strengthened bits....maybe someone else here could provide part no's or something to identify them.

  • Like 1
I think you would be doing pretty well to get a good series 3 box for 1100. The trouble with 2nd hand boxes is that unless you can open it up and look before you buy you are never sure what you are getting.

For the power you have listed and you have $3ish k to spend without doubt go an aftermarket gearset like an OS....I've seen way too many std boxes in GTR's break with that power (granted it was track use). If you don't have the money then try an find a good condition 2nd hand R33 box and as long as you don't have a solid center clutch and are fairly gentle with it it should last a while.

All I know is that the series 3 boxes have stronger syncros and a few other strengthened bits....maybe someone else here could provide part no's or something to identify them.

I don't know if it helps but here ya go:

Series 2 box:

Part Num: 32010-12U00

Series 3 box:

Part Num: 32010-12U10

Nissan list 32010-12U10 as the "alternate part" for series 2 but list 32010-12U60 as the alternate for series 3 R33 GTR.

Looking inside the box itself theres a load of parts to compare and im lazy.

I don't know if it helps but here ya go:

Series 2 box:

Part Num: 32010-12U00

Series 3 box:

Part Num: 32010-12U10

Nissan list 32010-12U10 as the "alternate part" for series 2 but list 32010-12U60 as the alternate for series 3 R33 GTR.

Looking inside the box itself theres a load of parts to compare and im lazy.

Thanks for your help Kris, hows your gtr going? Did you end up with those GTSS's?

Buying them soon - heading to Japan in January and picking them up there.

Car's going well though.

You bought a S3 now? You found one you liked?

Yeh, got a good deal on this one from a forum member. When i rectify this gearbox issue i will transport the car upto Mackay as my dad just bought a house there so now i have somewhere to keep an extra car. Was thinking to go 34 but this one has some tastefull mods and was a lot cheaper. As it happens my mate wants to sell his 34 at bargain basement now, its very tempting but i just bought this car and i am not ready to let it go.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...