Jump to content
SAU Community

Recommended Posts

this little runt called like 5 times saying ''i won free adidas shorts'' and shit like that, as soon as i started paying him out,

he giglled like a little school girl!!

and then i said optus was tracing his number and he hung up strait away.....

so.........th reverse phone book is???

shame about the defect scott, least you got a few days to drive it around. girl i work with was defected by our friendly officer neil in her 180 not too long ago.

also, i love finding random shit for the s14 on yahoo and import monster, i see you lurking ben, you know you want it. :P

woot

1st warning

lol you landlubbers you, not appreciating my "neil"-love (in a pure manly way of course)

muahahahaha !

fk it. karma is a bitch I say. always has been & always will be.

we'll see....we'll see.

also, i love finding random shit for the s14 on yahoo and import monster, i see you lurking ben, you know you want it. :P

That's cool as f**k. I was either going to do either leopard print or Luis Vuitton Door trims/shifter boot/cage padding/cam covers.... but thats awesome.

Got better things to spend $350 bucks on ATM though... Like camber arms... :P

I played around with my Coilovers tonight.... I cant go any lower without smashing the kit to pieces on ripple strips... Just how I like it. 25mm spacers and rear camber arms by this weekend.

DSCF0301.jpg

lookin good ben, huge improvement with the stickers gone, lv print everything sounds like a laugh.

hmm, 2000 posts and i didnt even notice...

Edited by scandyflick

Well since its my 21st :P tomorrow i think SA SAU should donate to me a:

Fully built RB26/30

Twin GTRS's

Full Bride interior

East bear rear bar/sides/ z-tune front

think that isnt to much.

Much love Luke ;)

Edited by Luke_ENR34
Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...