Jump to content
SAU Community

Recommended Posts

"Premium100 is a high performance petrol with an octane of 100, which is the highest rating available in the Australian market. Ethanol is a natural octane enhancer - adding 10% ethanol to petrol boosts its octane number and its performance. Ethanol helps the other components in petrol burn more completely. It also has a cleaning effect on the cars fuel system. Premium100 will give your car more zip! "

reading from that it should b better then BP ultimate. i might have to give it a try... i fill up tuesdays so might use it 2moro. any1 tried it?

Just be careful with ethanol blend fuels! I put some 98/10% ethanol in mine and the knock reading skyrocketed. Was tuned on Ultimate 98, tuner said that any ethanol blend fuel is trouble unless you retune for it. Due to the amount of extra fuel needed and less timing because of higher burn rate. My knock went from 30 on ultimate to over 200 on ethanol blend!

Oh and Damo, go for the chrome/orange globes. Last thing you want is nice clear side markers with daggy orange globes.

I am speaking to Luke_ENR about it, which seems to be clearing it up a bit for me.

I get the 040 in the cradle, but it doesn't go back into the tank. I now have a theory that the end/base of the 040, needs to be in the same position as the OEM pump. I was mounting the 040 a little bit further down, where the "C" bit of the cradle is, was where is was putting the line on the 040. the "C" bit, holds the OEM to the cradle as it has the pickup go through it.

ffs I couldn't have imagined it being so frustrating trying to buy a "near new" car .... I think I am on a winner this time - we will see what the mechanical check picks up on THIS one tomorrow.

pritty sure there is a guide on the site??

also i thought that the 040 is not a direct fit replacment?? but maybe thats just for gtr's

It isnt, you need to modify the cradle...but i think i know what to do now. I did look at the guide, it helped me a bit.

ffs I couldn't have imagined it being so frustrating trying to buy a "near new" car .... I think I am on a winner this time - we will see what the mechanical check picks up on THIS one tomorrow.

lol. turned into quite the mission for you. fingers crossed this one pans out. sedan or coupe?

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Started sifting thru my brakes to decide which ones I will run on Clem   Made me think I should just put them all on Silver...for when brake fade just isn't an option   Should be able to bump rotor up from 343x32 to 348x36 off Supra. Not sure if the Supra annulus is right for the Alcons or APs but trying g to find a used Supra\M4 rotor to test fit The Alcons seem to gain 1-2mm clearance which all helps  
    • So car is getting a few mods to the cage and some jacking points welded in Meantime Ol Silver gets a new gearbox and shiny clutch.  Old Box is being set aside for Clem  
    • Probably speedometer itself if the odometer is ticking. If the needle is stuck from a bit of grease or something that can cause it to stay at 0. Or a cracked solder joint in the speedometer can do it too.
    • Thanks Fella’s   to take this off topic and to elaborate a bit more. I have an rb25/30 going into a r32 GTST.. expected to make around 600-700hp. Would you?   A) R34 GTT box   B) CD00#?  I’ve seen a few posts about the CD swap and sounds fairly involved with making it fit etc but if it’s worth the work then I’ll go that way
    • Lower at the hubs. Funny I forgot to mention that part. Do this pull here I turned the camera off too soon but the graph shows a drop at the top and that was because the pipe from the turbo blew off. The tuner said we could’ve made possibly another 15 whp. He also added if I switched to ethanol we could up the boost some more as well. I was comfortable capping it at the most of 20 pounds. Turns out the turbo pipe just needed a new worm clamp. Got home replaced that then did a third gear pull from 3k to 7200 rpm and the power was great to the top. I just got an ecu mounting bracket from IEE that I need to try and get everything to fit well. It’s a PITA to get the harness and ecu fit properly behind that kick plate 
×
×
  • Create New...