Jump to content
SAU Community

Recommended Posts

yeh thats what im thinking matty..

also, just picked up my rolla from workshop to have a $710 bill..

what was done?

diff locked, vlturbo pump supplied by workshop)(its external so 5min job), indicator switch ($30), oil filter ($15), tighten back brakes (handbrake still doesnt lock), compression test..

7.5hrs labour to do that?? $500 just for labor? is this correct or should i not go there again?

7.5hrs labour to do that?? $500 just for labor? is this correct or should i not go there again?

If it was 7.5 hrs then $500 is a good price. I pay around the $85+gst mark per hour

I have nfi about mechanics so I dont know about the time, but given the list of stuff u got done, it wouldnt surprise me if that were about right

-D

i was gonna say, whats coming next :)

It'll be another 180 to do that 25 conversion on. with all the parts that would be coming out to do the conversion i would be basically parting out the whole car so I'll sell the current 180 and start again with another stocker.

for anyone thats keen, a few of us are going to the Lakes hotel to watch the game tonight.

141 Brebner Drv

West Lakes SA 5021

if you need my number for anything, shoot me a pm. Myself and Adrian will be there at around 6ish, game starts at 6:30

xoxo

Should be a mint game, Carn the Crows :)

Got my coilovers in, fully wound down it sits lower, but not as low as I would like but ohwell,

I got something coming that will be my fitment pig :) aha

Edited by Weezy
Should be a mint game, Carn the Crows :)

Got my coilovers in, fully wound down it sits lower, but not as low as I would like but ohwell,

I got something coming that will be my fitment pig :) aha

shouldve got a set that are base height adjustable. run as low as you want without having a crazy uncaptive spring.

but yeah, run it a little high, bout the height of heslo's car would be ideal, low cars sucks.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • all brand new unit from Tomei, fluid, bearings, etc. Tomei said they call it a 1.5 lsd because its 100 percent lock up under acceleration and 50 percent under deacceleration.  as I mentioned I used their fluid, install and their break-in procedure, (alot of figure 8's) but even when driving straight, or even slowly backing out of garage for first time, (at 2 mph) then driving to and from figure 8 parking lot, each tire in the rear would sporadically grab, skip, bounce, shutter and skip, shutter back a force I could feel causing clutch to slip then grab, at any speed. shaking entire car. I removed unit, since I put stock back in and all is fine, via process of elimination, its something with the lsd unit itself. I wasn't going to beat up the entire car more or change anything else for no reason as I had a feeling something in the lsd itself was wrong as everything was fine before this alone was installed and I rechecked over everything else after first time backing out I suspected an issue. I'll probably sadly already need new tires now just from trying to drive it 5 miles and performing the figure 8 break in. but if someone has any ideas I'm all ears 
    • Ok thanks..that was my second question if i can somehow bypass this even with Nistune(that is all i have right now...aparat from stock ECU. So with some aftemarket it can by "bypassed" or make it work?  I know there is Link or Haltech (mainly used). We have ECUmaster here so i will gather some info about it.
    • Yes. You will need to get the original boost sensor and wire it in. That is.... if you plan to use a stock ECU - even a Nistuned ECU. The Nissan ECU will not operate correctly without it connected. And yes, it will do annoying stuff like you are experiencing. You will almost certainly be better off with some aftermarket ECU, than trying to hunt down rare sensors.
×
×
  • Create New...