Jump to content
SAU Community

Recommended Posts

yes RB24DET

Tomei pistons, GTR crank, rods etc...

hence with the way rb20's and rb25's flow gasses differently, i'm after some sort of assistance in trying to figure out best setup for my car. also assumin my 20 based engine will rev more, also after opinions, that is why i would like peoples opinions on my questions.

thanks for the links, i have spent time reading them, and in mafia's thread he is relating to RB25... but i will have another look at them

thanks

-Matt

Edited by huddy
  • Replies 56
  • Created
  • Last Reply

Top Posters In This Topic

If you stroke out the bottom end and leave the head untouched it will make its peak power earlier in the rpm and nose over earlier. in other words rev less.

Your going to have to get the head breathing better with a set of cams.

Stock ECU that dip is normal, its the rich/retard kicking in most of the time... plus average mapping i would suspect.

PowerFC/Tune = gone.

I have to say that I've seen that mid range dip more than a few times. Ignoring any stock ECU that's going into rich+retard, it's more with unopened engines but uprated turbo specs and with a new ECU. I see that Lithium has a Link setup.

Which area of mapping should be used first to attack the problem? ie fuel or ignition? If it is fuel (and assuming that the AFR in that area is a "nice" repeatable value, should it be leaned off?

i too have seen that dip in plenty of RB25 dyno's... and thats with aftermarket ECU's, stock bottom ends and supporting gear with decent turbo's... any idea what the cause is there??

Huddy: the prob with making 300 rwkw with your set us is you have the bottom end support to do it... but the head is still an rb20 head... it just wont flow the air to support the big numbers... no matter what turbo you run.

I have to say that I've seen that mid range dip more than a few times. Ignoring any stock ECU that's going into rich+retard, it's more with unopened engines but uprated turbo specs and with a new ECU. I see that Lithium has a Link setup.

Which area of mapping should be used first to attack the problem? ie fuel or ignition? If it is fuel (and assuming that the AFR in that area is a "nice" repeatable value, should it be leaned off?

The fuelling on mine was nice and consistant, and the timing is all fairly sensible though we / he didn't play with the VCT point. The tuner is a very accomplished tuner, he tunes some NZ GTR who went over to Australia last year and turned a few heads.

i too have seen that dip in plenty of RB25 dyno's... and thats with aftermarket ECU's, stock bottom ends and supporting gear with decent turbo's... any idea what the cause is there??

Huddy: the prob with making 300 rwkw with your set us is you have the bottom end support to do it... but the head is still an rb20 head... it just wont flow the air to support the big numbers... no matter what turbo you run.

time to buy Blinkies head then

Mach Go Go style 405rwkw on low boost

rb20 head

http://www.geocities.jp/akfw1_rbx32/free/car.html

rb20 head 3lt bottomend 600ps hmmm list it as a 25 head in specs?

http://www.eonet.ne.jp/~7thmeister/2003914zen.htm

2.2lt rb20 272 cams 500 ps http://www.dragster.st/dragster/mizo/mizo.html

Edited by 1400r
I have to say that I've seen that mid range dip more than a few times. Ignoring any stock ECU that's going into rich+retard, it's more with unopened engines but uprated turbo specs and with a new ECU. I see that Lithium has a Link setup.

Which area of mapping should be used first to attack the problem? ie fuel or ignition? If it is fuel (and assuming that the AFR in that area is a "nice" repeatable value, should it be leaned off?

Dunno, i didnt tune the car, i leave that to my tuner/builder.

But there must be something people arent looking at/changing as no car i know of that gets tuned has a problem and a few RB25s have been done there.

I dont think its bottom end related as that largely has no effect IMO.

I guess it comes down to what the budget will stand, and whether you can feel a difference on-road.

VCT change point on a mechanically standard engine can have marked impact, but usually in a negative way if you alter it a long way from standard. But + or - a couple hundred rpm might be worth a try.

I've seen using an adjustable cam gear also work well in terms of smoothing the torque curve - but no actual increase in my case. Just minimised the peaks/troughs so it was evident the engine was running in a happy mechanical zone.

With that slightly saw-tooth appearance, I'd think that the ignition map might be worth a look. If it was mapped to the best output without knock, some columns will take less timing, meaning that as you advance through the rpm range the map is not moving smoothly through a curve. Can give the up/down appearance I'd commented on.

None of this is a smart-arse commentary, just looking to see how the end result came about and whether it's possible to improve with comparatively little effort or $$. I like to know the how/why rather than just leave it to a tuner.

The fuelling on mine was nice and consistant, and the timing is all fairly sensible though we / he didn't play with the VCT point.

Shit hey, i had just ordered the GT3082r with the .63 the day before i posted my question. Now i read u guys reckon it'll be crap and i've got it! I hope your all wrong lol. I'll post the dyno results when i get it all fixed up.

I have to say that I've seen that mid range dip more than a few times. Ignoring any stock ECU that's going into rich+retard, it's more with unopened engines but uprated turbo specs and with a new ECU. I see that Lithium has a Link setup.

woudlnt this have something to do with the Profiles on the cams?

Edited by silverbulletR33

I'd say probably, yes.

He should be in a position to work with what he's got though. I posted a few ideas on #51.

Changing to non-standard cams may well just move the characteristic (I won't call it a problem) around and upwards. The saw tooth torque curve I would think is the bigger issue to address. And there are things that can be done that cost more in the way of time than anything else.

Again though - Lithium has got a generally good result. I'd just like to see something done to make it "happy".

woudlnt this have something to do with the Profiles on the cams?
Changing to non-standard cams may well just move the characteristic (I won't call it a problem) around and upwards. The saw tooth torque curve I would think is the bigger issue to address. And there are things that can be done that cost more in the way of time than anything else.

Again though - Lithium has got a generally good result. I'd just like to see something done to make it "happy".

Yeah me too. For what its worth, you really can't feel any of it on the road. All passengers etc perceive it as just building up and having strong power all the way through, the only "weakness" is that the thing doesn't go straight to 15psi and hold it. If it did that it'd be so much more solid, nonetheless there are definitely gains to be had by removing that slight dip.

The plan is next year to go to a built motor etc and then give it some boost and revs, this tune was just to get it safe and fun to drive - not to hunt every last hp :thumbsup: For what its worth, I gave it a run on a rolling road dyno for fun and the dip wasn't anywhere near as extreme.

  • 2 weeks later...

did you guys get custom lines made up to suit? just got my 3076r... :)

LITHIUM

-i cant see pics of your dump, can you please post up, mine phsically looks the same as yours with the antisurge front, and same stye rear exhaust housing.

-how did it go for standard intercooler piping to the top of the turbo? (well maybe not standard, as mine had previously been modded for the hks turbo...)

-was there any difference noticably with the change in manifold? (even noise??)

cheers

-Matt

Edited by huddy

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • For these last 7 years of ownership, I've always had to use a small scissor jack under one of the front tow hooks to raise the front just enough so my low-profile jack fits under to reach my subframe jack point. I'm beginning to get annoyed of always having to do this. Are there any lower low-profile jacks that fit under the gtr lip on a dropped car?
    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
×
×
  • Create New...