Jump to content
SAU Community

Recommended Posts

There may be an easier way but a mechanic I used to work with gave me a suggestion.

You will need a clutch alignment tool or something that fits into the spigot bearing fairly tightly (wooden rod) and some grease.

Pack the inside of the spigot bearing with as much grease as you can.

Now get your alignment tool or the other thing that fits and push it into the bearing.

Push on it and the grease should force the spigot bearing out as it has nowhere to go.

May get a little messy.. but it should come out. It was a while ago but I'm sure this is how my mate and I got his out when changing his clutch. I can't really remember it so hopefully that's a good sign that it was quick and easy.

Last one I changed, packed it full of bearing grease, used a wooden dowel that was a close fit inside the bush, and just tapped it with a hammer and the hydraulic action of the grease on the back of the bearing popped it out.

Easy.

  • 3 weeks later...
  • 1 year later...

Im a mechanic and have done this many times. Obviously, a Spigot bearing puller is the BEST way to go, but its not common to have one. What I do is similar to the methods mentioned above, but a lot less messy. Get yourself a punch, or rod that has a snug fit through the bearing. Instead of grease (as mentioned above), grab yourself a handfull of toilet paper (yes....you heard right). Tear bits off, wet it, push it in the hole, and use the punch to compress it. Continue doing this and the bearing will eventually pop out from the pressure that the bog roll is exerting from behind.

As i said, I have used this method at least 50 time over the years, and it has NEVER failed me......

yeah, grease is the best way. especily if its rooted.

i fine a 1/2" extension fits good inside it. pack it with grease and hit it with a hammer hard. might take a few gos but it will come out :P

grease is my preferred method...but if it doesnt budge run a 2mm drill into it along one side and use a small cold chisel to break it along the drill hole. A large screwdriver should then be used to remove it.

My spigot bearing was chipped the last time i put the box back on, which resulted in it being noisy.

How long can i drive with it being noisy like this? If the noise gets worse ill obviously have to fix it, but in the meantime?

Sounds like a straight cut box at the moment lol

when i did a manual conversion to my mates 32 4door i got a nut that was a firm fit and tapped it in with a hammer then tack welded the nut to the spiggot bearing then threaded the slide hammer into the nut and bang bang it was out, we tryed the grease method and it ddnt work it wouldnt budge. i found that was quite an easy way. also NYTSKY if u leave it too long like that it mite wear a grove in ur input sharf to ur gearbox, then its rooted.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I've looked up the parts number (41011AL501). It's around $700 OEM. Usually our Infiniti G35 here in Canada have interchangeable parts with my Stagea but the parts number are not the same. I have looked around and it seems the JDM 2005 V35 Skyline (which is the same as our G35) has the same caliper but I cannot confirm. And I can't find a repair kit. The inner brake pads drags on the rotor, seems to be rusty piston. Thanks for the info by the way
    • This coupled with 6-9 speed autos with ridiculously short gearing is why these modern shitbox cars always seem so fast off the line. If it wasn't for those things, Raptors would not seem fast. The problem we have is there is a driveability gap between a more gentle take off and a wheelspinning sideways launch. The difference between ankle flex required to achieve one and ankle flex required to achieve the other is about 0.5°.
    • Yeah I think I'm also with the opposite here. It's 'hard to keep up with traffic' because in the real world I'm accelerating with 15% throttle and they are pinning it. It feels like I'm being an overt dickhead at anything above 15% throttle, so the car sounds like I'm being an overt dickhead to keep up with/get ahead of traffic when I'm really just trying to drive with traffic. There would be no issue 'keeping up with traffic' if we used the same level of throttle input/aggression to drive around. People really do just drive around with their foot nearly pinned in econoboxes.
    • To be fair it's the other way around. 300kw is boring in a modern Golf or BMW. They are so competent / well-engineered / devoid of emotion that you have to go stupid fast to feel anything. Whereas the <300kw RB still makes all the right noises and it feels good to drive. Can pull off at the lights with the turbo whooshing and the blow-off pssshing and feel like the coolest kid on the block. Just don't look to the side where you'll see the bored housewifes in their shitbox Yaris/Corolla/Camry that kept up because you didn't go fast at all
    • 300kW is so boring in a Skyline, you'll get spanked by someone's mum's Golf with Alibaba pipes, and an email tune.
×
×
  • Create New...