Jump to content
SAU Community

Recommended Posts

There may be an easier way but a mechanic I used to work with gave me a suggestion.

You will need a clutch alignment tool or something that fits into the spigot bearing fairly tightly (wooden rod) and some grease.

Pack the inside of the spigot bearing with as much grease as you can.

Now get your alignment tool or the other thing that fits and push it into the bearing.

Push on it and the grease should force the spigot bearing out as it has nowhere to go.

May get a little messy.. but it should come out. It was a while ago but I'm sure this is how my mate and I got his out when changing his clutch. I can't really remember it so hopefully that's a good sign that it was quick and easy.

Last one I changed, packed it full of bearing grease, used a wooden dowel that was a close fit inside the bush, and just tapped it with a hammer and the hydraulic action of the grease on the back of the bearing popped it out.

Easy.

  • 3 weeks later...
  • 1 year later...

Im a mechanic and have done this many times. Obviously, a Spigot bearing puller is the BEST way to go, but its not common to have one. What I do is similar to the methods mentioned above, but a lot less messy. Get yourself a punch, or rod that has a snug fit through the bearing. Instead of grease (as mentioned above), grab yourself a handfull of toilet paper (yes....you heard right). Tear bits off, wet it, push it in the hole, and use the punch to compress it. Continue doing this and the bearing will eventually pop out from the pressure that the bog roll is exerting from behind.

As i said, I have used this method at least 50 time over the years, and it has NEVER failed me......

yeah, grease is the best way. especily if its rooted.

i fine a 1/2" extension fits good inside it. pack it with grease and hit it with a hammer hard. might take a few gos but it will come out :P

grease is my preferred method...but if it doesnt budge run a 2mm drill into it along one side and use a small cold chisel to break it along the drill hole. A large screwdriver should then be used to remove it.

My spigot bearing was chipped the last time i put the box back on, which resulted in it being noisy.

How long can i drive with it being noisy like this? If the noise gets worse ill obviously have to fix it, but in the meantime?

Sounds like a straight cut box at the moment lol

when i did a manual conversion to my mates 32 4door i got a nut that was a firm fit and tapped it in with a hammer then tack welded the nut to the spiggot bearing then threaded the slide hammer into the nut and bang bang it was out, we tryed the grease method and it ddnt work it wouldnt budge. i found that was quite an easy way. also NYTSKY if u leave it too long like that it mite wear a grove in ur input sharf to ur gearbox, then its rooted.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • It's almost certainly a reluctor generating an "AC" waveform. No, ECUs don't generally read those - they're usually set up for PWM square wave 0-5v stuff.
    • Working through possible solutions of converting my mechanical speedo.    Anyone know what type of speedo sensor the factory r34 gtr getrag has ? what the output is ? I assume its not a VSS and more a voltage like earlier speedo sensors ? Can an ECU read it ?  
    • roof rail delete used to be a thing, they were made locally for a while too
    • I can get more photos of it here soon and I plan to make a thread detailing the process. I received the car this way and it sorely needs refinishing. That is probably the most appealing photo of it. Up close it is fading, cracked, and needs to be re-glued. Depending on their condition I'm on the fence between refinishing or making a new set.  Another angle hiding the pimples and razor pumps  
    • According to this thread the RS4V with build plate RC40 comes with the R200 diff @ 4.083 ratio as well (mine has said RC40 denotation). We may need to check if the axle stubs are the same pattern as well. The auto subframes have longer axles. However I think yours being a later Series 2 as well, we should have the same bolt pattern for the diff stubs. Unless your upgraded rear also has upgraded axles. Either way, I would not be opposed to pulling the covers to check so I can inspect that  fancy rear core  Also I don't have HICAS. I don't believe that should change things but I hope the people here with heaps more experience than me can correct me if I'm wrong   Let me know if you want to attempt to make this work and I can get some pictures of mine from under the car. 
×
×
  • Create New...