Jump to content
SAU Community

Recommended Posts

I'd like to know if the front and rear diffs are the same ratio difference between GTR and GTS4? I recall the GTS4 rear was about 4.3 and GTR rear was 4.1

What about the front diffs? If they are 4.3 and 4.1 respectively, this means a GTR box will fit, yes?

What other differences are there, are the ratios the same or different?

Any other info I may need to know?

Cheers

Front and rear diffs are 4.3 in a GTS4. GTR boxes do fit into a GTS4 with no problems, final drive ratio gear needs to be changed tho from the 22 tooth GTR one to a 21 tooth GTS4 one... or something like that.

No. The ratio of the front diff is the same as the ratio of the rear diff. Otherwise, the front and rear axles would be driven at different speeds.

What funky means is that the speedo drive gear needs to be changed (as I have just done after I put a Stagea diff set @4.083 in my GTS4 - GT-R drive gear replaced GTS4 drive gear)

GT-R = 4.111, GTS4 = 4.375

Stumbled upon this a little while back.

Gearbox ratio's.

Note the RB26 gearbox has longer gears everywhere. :P

You can work out the diff ratio via the speedo drive tooth count.

As others have said 21 = 4.363 (gtst) & 4.375 (GTS4) and 20 = 4.11 (GTR etc)

20tooth is also used for the 4.08.

post-382-1192836388_thumb.jpg

Interesting. Can you remember seeing a parts code on the outside of the gearbox referring to what model it is?

Bit of a pain getting under my car without throwing it up on ramps.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • That's not a transistor --- it's marked ZD1 which makes it a zener diode. As to what the breakdown voltage is, not enough there to divine.
    • Hi all, Long time since I've posted here. Looking for some advice on what I can remove to further identify the cause of my issues.  I can move the passenger seat forward and back but the knob used to adjust the seat angle is pretty much free spinning, there's very little resistance.  Removing the side cover I can see that the chain is intact but the shaft for the adjustment spins without the gear attached to it moving.  What's my next step for disassembly here? Is this a common fault? Just being a little cautious as I didn't want to start removing bolts for a spring to fly out or something equally as stupid.  Cheers
    • The incentives are mostly the same, yes. Ethanol is cheap compared to the cost of doing 98-100 RON with crude oil alone. 87 to 93-94 AKI all with E10. In 2020 Canada mandated E10 as a part of their "renewable fuel standard" and is supposedly going to go to E15 in 2030. In California where there are only 8 refineries with two threatening to shut down next year it's been over 20 years now of E10 and 91 AKI maximum because there's just not enough refinery capacity or crude oil supply relative to the demand for premium unleaded fuel. And CARB's low carbon fuel standard means functionally none of the diesel available at the pump is made from crude oil anymore. It's almost all entirely 20% biodiesel blended with 80% renewable diesel (hydrotreated vegetable oil) now. The number of gasoline vehicles that support E15 or higher ethanol concentrations is surprisingly low, I can't imagine it being wise to play tricks like this without flex fuel sensors in most of the fleet.
    • It's almost certainly the same as the one next to it. Have a fish around amongst these hits https://www.google.com/search?q=surface+mount+transistor+m33&sca_esv=9cb49794e0b2005d&source=hp&ei=2vJ5aNjTB7Kw0PEPldnS8QM&iflsig=AOw8s4IAAAAAaHoA6qkfmF6XcygtrZ4Vu9f92NXF_RFd&ved=0ahUKEwjYqIPP7MWOAxUyGDQIHZWsND4Q4dUDCA8&uact=5&oq=surface+mount+transistor+m33&gs_lp=Egdnd3Mtd2l6IhxzdXJmYWNlIG1vdW50IHRyYW5zaXN0b3IgbTMzMgUQIRigATIFECEYoAEyBRAhGKABMgUQIRigAUjKCFAAWABwAHgAkAEAmAHfAaAB3wGqAQMyLTG4AQPIAQD4AQL4AQGYAgGgAuYBmAMAkgcDMi0xoAfMBLIHAzItMbgH5gHCBwMyLTHIBwU&sclient=gws-wiz
    • South Australia, which is hardly as far behind as the rest pf Oz makes out, and who is also not a paragon of progressiveness (read that as over-legislation) in the area of vehicle standards, has this to say on the subject: Adjustable coil-over suspension Aftermarket adjustable coil-over suspension components are suspension units that incorporate an external thread on the main body and corresponding threaded spring saddle that allows the vehicle's suspension height to be varied. If fitting aftermarket or coil-over suspension components you must submit an Application to modify a light motor vehicle form and a report from a light vehicle engineering signatory (LVES).
×
×
  • Create New...