Jump to content
SAU Community

Recommended Posts

I have a series 1 R33 GTS-T.

When i reverse up the driveway i can hear a rattle that sounds like it's coming from the top of the right rear shock. I checked that all the bottom of the assembly is tight so it seems to be the top nut / nuts have come loose. I removed the carpet panels from inside the boot and can see the surround where the shock would sit inside but cannot find a rubber to remove to tighten the top nut / nuts. I searched through these forums and found 1 reference to it but it was based on an R32.

R32/33: Replacing Shocks / Installing Coilovers

It looks to me like i may need to remove the back seat, then the parcel shelf to get to it?

Any help or advice would be much appreciated!

Link to comment
https://www.sau.com.au/forums/topic/190550-r33-gts-t-rear-shock-removal/
Share on other sites

no problem.. alternatively you can smash the rear window and rip out the parcel shelf... thats how i removed them when my car was written off. :rolleyes:

After reading the "Skyline R33 Rear Seat Removal Pictorial Guide" (minus pictorial!!!) it might be easier to smash the window!

Skyline R33 Rear Seat Removal Pictorial Guide

its not *that hard*...

undo the bolts in the bottom of the seat, then the bottom will unclip (with a bit of force, i usually stick my breaker bar though the loop, and give it a pull upwards),

undo the bolts in the bottom corners of the top of the seat, and it will lift up and off,

then the parcel shelf should just lift off, and you are done.

Takes about 5 minutes to have the whole back seats and parcel shelf out once you've done it a few times. Trickiest bit is getting the seat base out of the clips if your afraid you'll break something.

My advice is to have a crowbar and dont be afraid to break the clips as they wont.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After using a protractor for an actually accurate assessment of what is required,  and by NOT using my uncalibrated eyeball I worked out I need a 25° silicone bend from the TB ro the MAF, but, my choice was either a 30° or a 23° (23° is a weird spec), so I grabbed the 23° one from Raceworks I also grabbed 1mtr of 3" straight from Just Jap, I needed 350mm, but they only had 300mm, or 1mtr lengths....meh Also ordered a 1/2" hose bulkhead fitting from fleabay, this has a smoothish mushroom looking head (they are designed for below the water line of boats) that will fit inside the bend, the hose bit and threaded bit looks to long, but nothing that a hacksaw cannot fix if required, the hose will then just get jamed on the threaded bit up to the retaining nut Fingers crossed and the unsightly amount of hose clamps will be reduced down to 4 once all the parts arrive 
    • Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
    • No. I think it might be the AFM. Hence the use of the terms "swaptronics", which implies the use of swapping out electronics for the purpose of diagnosis. It's about the only way to prove that a small/niggling/whatever problem with an AFM or a CAS or similar is actually caused by that AFM/CAS/whatever. A known good item swapped in that still gives the same problem is likely to be caused somewhere else. They're all the same. Spraying AFMs with cleaner is an each way bet between cleaning it and f**king it.
    • Oh wow! This might actually work amazingly. Do you know the ratio of the diff? I was told the only thing you need to make sure of is if the front & rear diff ratios are the same. Ours is a 4.083 Thanks!
×
×
  • Create New...