Jump to content
SAU Community

Recommended Posts

R34

1 - First pull out the ashtray and undo the screw behind it.

2 - Pull up the gear stick surround and undo the 2 silver screws at the bottom left/right of the storage bin.

3 - Using a thin flat blade screwdriver on the left side, prise out the 2 vents at the top of the console and disconnect the unit.

4 - Undo the 2 silver screw at the top of the heater controls.

5 - Pull out the heater controls, radio & stage bin (all in a cage together).

6 - Remove the radio from the cage (2 screws each side) and fit your radio.

7 - Refit going from step 5 back

Link to comment
https://www.sau.com.au/forums/topic/190825-head-unit-removal/
Share on other sites

Nice guide :/ here's the 32:

R32

1. Pull out ashtray like below, undo two screws behind it

2. Flathead screwdriver under the rear of the center console, push up, it will pop out

3. Flathead screwdriver under the top half of center console, pops out, remove center console, or turn it around

4. Undo 4 screws, two either side of headunit, pull headunit out

5. Undo cage holding onto headunit, refit to new headunit, finish wiring off and put back in hole

6. Refit going backwards from 4 :D

was I your guinea pig chris???

keeep it on topic guys.

my intent was to get this stuck to the top so everyone would stop asking how to get them out and stop filling my PM box u :spank:

jon,

can't remember done too many of the things.

  • 3 months later...

R33

remove ashtray

remove 3 screws

unclip panel around shifter

remove two more screws below radio area.

unclip main surround

unclip wiring from: clock,hazards,rear demist , A/C temp sensor, electric mirrors

remove main surround.

remove 4 screws from radio assy.

unclip HVAC and radio wiring.

contact me for pocket,harness and antenna adapter

remove 4-8 screws from radio and put yours in place.

reassemble.

Edited by Chris Rogers
  • 2 months later...
R34

1 - First pull out the ashtray and undo the screw behind it.

2 - Pull up the gear stick surround and undo the 2 silver screws at the bottom left/right of the storage bin.

3 - Using a thin flat blade screwdriver on the left side, prise out the 2 vents at the top of the console and disconnect the unit.

4 - Undo the 2 silver screw at the top of the heater controls.

5 - Pull out the heater controls, radio & stage bin (all in a cage together).

6 - Remove the radio from the cage (2 screws each side) and fit your radio.

7 - Refit going from step 5 back

OK I used Chris's instructions and a couple of extra things that he told me about so here is a slightly more detailed description with pics.

1 - First pull out the ashtray and undo the screw behind it.

The ashtray just pulls out with no significant force needed. I just pulled on the open lid.

Pic1.jpg

2 - Pull up the gear stick surround and undo the 2 silver screws at the bottom left/right of the storage bin.

This takes a bit more force, I pulled from the back near the handbrake and levered it up with my fingers. I also pulled off the shift knob at this time but you could probably do it with it on but I thought it would be easier with it off. There are 2 screws at the front of the knob, put the shifter right back in low to get easier access. It takes a little bit of maneuvering to get the surround over the front of the shifter indicator and be careful not to scratch the vinyl with the hard edges of the surround. Unplug the lighter, lighter surround light and steering wheel shift switch. All plugs have a release tab, push it in or you will get real cranky trying to get em off.

Pic2.jpg

3 - Using a thin flat blade screwdriver on the left side, prize out the 2 vents at the top of the console and disconnect the unit.

This is the panel that houses the 2 vents and the hazard switch. I used some masking tape around the screwdriver to avoid scratching the vinyl when levering. Unplug the plug at rear.

Pic3.jpg

4 - Undo the 2 silver screws at the top of the heater controls.

Pic4.jpg

5 - Pull out the heater controls, radio & stage bin (all in a cage together).

I put some toweling over the lower console area to avoid scratching the vinyl.

Pic5.jpg

6 - Remove the radio from the cage (2 screws each side) and fit your radio.

I undid a couple of extra screws to "open" up the cage a bit to allow the radio to be removed and the new one installed more easily and without scratching anything.

Mine had the aerial adapter already fitted as there was already an aftermarket deck installed but the previous fitter had butchered the wiring loom so it was a bit more work to re-wire all the wires in a decent manner but if you are removing the stock deck then get the correct plug adapters and aerial adapter available from Chris or some auto outlets. I also bundle any wire slack in some padded tape to avoid any rubbing or rattling later on.

Pic6.jpg

7 - Refit going from step 5 back

I connected everything up and tried all deck functions before re-fitting the cage permanently just in case but luckily for me all went to plan.

Hope this helps, Mark.

  • 5 months later...
  • 1 month later...
  • 1 month later...

this really helped me out!!

I just thought i would add that to get the gear surround out it actually a little lever point for you to put a screwdriver by the handbreak at the back. i was having trouble working out how to get it off untill i spotted that.

  • 3 months later...
  • 3 months later...
  • 2 weeks later...

might sound stupid but, how do u disconnect the plug behind (the wire connection) the car lighter, there are two of them, one is bigger than the other... seems like it would not come off however from the picture above, obviously 2KR34 can took them it off..

i just dont want to break it because i use it for a lot of thing to charge my ipod, gps, and when i left my lighter.... basically half of my life depends on it.. :)

pls help someone

its for a 34 btw

cheers

bly

  • 6 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • It is a kunfine Android screen . Does anyone know the wirering diagram of the fuga ??
    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
×
×
  • Create New...