Jump to content
SAU Community

Recommended Posts

Hi, I am new to the forum and would like to know if anyone has destroyed their turbo on a Skyline? I have read a lot about not putting the boost over 12psi, but I am wondering if anyone has done this and caused damage, or whether it is just a myth. I know there has to be a limit at some point, is it 12psi or are there people out there running their stock R33 turbos at 14psi or higher?

What are your stories of disaster.

Link to comment
https://www.sau.com.au/forums/topic/19118-have-you-destroyed-a-turbo/
Share on other sites

Mine was running at 13psi quite happily turbo wise, although it was starting to ping a bit too much so had to wind it back to 12psi.

12psi I'd say is perfectly safe as long as you have a good tune and decent FMIC. My high boost has been that or 9 months or so with no adverse effects and some pretty hard driving occasionally. Depends whether its a series 1 or series 2 turbo.

As mine is a daily driver i often just run stock boost to and from places, so i wouldn't say i run 12psi all the time. People will also argue whether 10-11psi is more optimal in terms of overall performance too.

I have a R33 Series 1 and have been running 14psi for around 2 1/2 years now. The only problem I have had is the turbo sucked in and ate the rubber bung that the car yard put on to block the Bov return hose when fitting the atmo venting BOV. The same turbo is still on and going strong.

The previous owner of my car destroyed the stock turbo doing 15psi on his daily commutes to brisbane...tortured, replaced, and hi-flowed it in the end...saved me some big money :)

It runs 10psi now for daily driving, but can go up to 18psi, no sweat. Right now, that figure is a little too far fetched though

Skylines have been found by a lot of people to make better, more 'useable' power on around 10-12psi. Note 'useable'... No point running more boost if it aint doing much or downgrading performance and reliability. The fact of the matter is if you are going to boost, you need to mod and free up the airflow so that it is actually worth boosting in the first place. You'll find obviously that if you run a stock skyline on say 12psi, then have another with a cooler, exhaust, filter and tuned on 8 psi it will run a heap better and harder than the 12psi stocky. Boost does not just = power.

R33's really need an aftermarket ECU to take advantage or should I say unlock some decent power.

200rwkw isn't bad considering its a stock turbo.

The FMIC and ECU make a big difference to the R33's.

R32's pitty its not the same for the R32's. :)

Over 10-12psi the stock ECU starts doing strange power dip things.

I aren't running a computer now with my big turbo, cooler, exhaust blah blah and it still runs pretty damn well considering, however am expected to pick up around 25rwkw from computer they reckon, so on about 15psi tuned they said i can look at around 235-240rwkw which aint too bad :) But yes they do need a computer to run well, without one they jsut eat fuel and run very rich. Not good on the wallet believe me ha ha.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So the original radiator is leaking now. Looking at getting a fully aluminium one next. Am I correct in saying that the Series 2 Auto Stageas have a separate trans cooler from factory (located in between the rad and intercooler in my previous post/message).   Currently looking at Fenix $460, Blitz $700, GReddy $800, and KoyoRad $740. What are everyones thought on Fenix ( ive read a few comments saying theyre cheap Chinese rebrands etc and how their build quality is... well.. chinese...)  compared to the others? Worth the extra couple hundies?
    • Man, different parts but the same numbers is terrible @dbm7! And it doesn't help that most online shops don't list the part numbers at all. They just give a list of compatible models...
    • Slow when hot could also be because its getting more dynamic compression, OR things are getting a bit tighter once it is all expanded. If it were an earthing issue, typically I'd expect you to have it have issues all the time. Unless it's really a combination of both things. Where the higher compression, and things being a bit tighter, is giving that bit of extra load and you do need a slight clean up on the cables/connections.
    • Yeah, this is one of the most annoying things about nissan part numbers... I've got an unrelated example... Image is of the AT output shaft ~ they have the same part#, but clearly the shaft on the left is beefier design to that on the right ...the difference (essentially) is the 'lighter' shaft on the right, is for engines up to RB25DE (this includes RB20 variants) : the shaft on the left is for RB25/26DET(T)....are they interchangeable? Yes...but obviously one shaft is going to be stronger than the other...and, the lighter shaft is around USD115, but the heavier shaft closer to USD150...same part#... ...epc-data usually tells a tale ~ the amayama listing for 39100-23U60 has a note "Longest side is between 60 and 105 cm" ; no such info is there for 39100-23U70 ...and given the great disparity in price between the 2 parts, it makes me at least curious (to the point of caution) where the 'extra money' went? ...ie; these 2 parts have a cost difference that (to myself at least) isn't explained by 'plastic boot'...ie; with amayama there's AUD700 price difference ...plastic versus rubber?...I'm not seeing it like that...and 60cm ~ 105cm...??...that's a huge disparity....something hinky going on here... I'd try searching by VIN, not model... /2cents
×
×
  • Create New...