Jump to content
SAU Community

Recommended Posts

need 100k service, car is already at a place my friend told me were honest and bla bla bla, well the guy has had it for 3 days now he needed to order in the timing belt and some other shit, i thought i would be looking at around $800 not $1600

cant do much now as the car is has already been worked on but yeah,

its a 97 NA auto r33 it needed sparkplugs,belt,lube change ect,ect all brakes are in bad condition, auto tranny service

some feedback asap would be very much appreciated.

im going to be broke for a few weeks =/ :rolleyes::rofl::no:

Link to comment
https://www.sau.com.au/forums/topic/191243-100k-service-1600/
Share on other sites

timing belt can be had the same day... no need to be waiting 3 days for that stuff

even if they replaced all your rotors and pads I still can't see it being anywhere near $1600... but then again I haven't seen the invoice etc... get them to break down the costs for you, sounds a bit on the high side

ah didn't read the bit about water pump... still, they aren't very expensive... under $200... also you should be able to replace your pads for under $200... just some Bendix or Lucas would do the trick... in fact if you went for a nice cheap pad you could probably get in under $100... that said I'm not suggesting you get cheap brake parts... one area you don't want to skimp

Good idea to do the water pump as its a pain in the ass to get to. Should be a touch over $100 for a reasonable one, as should be brakes. Depends if the disks needed doing also... Spark plugs cost $25-$30 for six and isn't a hard job depending on what kind of plugs they used. Iridiums you're looking at $150-$200 for all 6.

Timing belt kit can be had for around the $300 mark. $10-$30 here and there for flushes, oils, filters etc all adds up too. Labour would be the big issue.

aparently he has put in platinum spark plugs? the guy said he wanted to put the water pump in because its hard to get too and he might as well seing that hes changing the timing shit.

im getting my car back tomorrow $1150 later, he wanted almost another $400 to do just the back brakes!!@@!!@? i think this guy is on crack. il go to brakes plus or something. im sure it will be cheaper.

100K service for my 34 came in around the 1k mark. Sourced my own parts to cut cost ie: Genuine Nissan Waterpump, gates belt, tensioner and idler bearings, seals. Labour was about the $500 mark which included replacing all fluids, filters, radiator flush etc..dropped my car in the morning and was completed same day in the afternoon.

Things to note: Always pre-book your car in and make sure they know exactly what they have to do. Source your own parts to cut costs, workshops will always charge a margin if they buy the parts. Confirm how long it will take and also costs so you don't have any nasty surprises when you pick your car up. It shouldn't take 3 days for a 100k service.

sounds like you just gave the car to him without running over exactly what you want done. might as well give him your pin number.

i paid around 1600 for mine with genuine parts. exhaust studs and gaskets and rocker cover gasket change was included in that price.

i think i paid 180 to get my brake pads changed and discs machined. 400 sounds abit excessive.

he wanted almost another $400 to do just the back brakes!!@@!!@? i think this guy is on crack. il go to brakes plus or something. im sure it will be cheaper.

No offense mate but I think your gonna be in for a very rude shock. It's a performance sports car, not a commodore and I think you will find you get what you pay for, especially with brakes. If you want to use cheap and nasty parts and cut corners, don't expect your car to perform to its full potential. Don't want to sound like a prick but you really need to do your homework and find out a lot before going to the service with mechanics and these cars and before committing any money or handing over the keys as I have unfortunately found out.

And to n15mo, while it is good to source your parts you will find that the mechanics will not carry out warranty without you paying the associated labour costs to their workshop, something that I decided not to skip last service and it has saved me about 300 bucks and counting.

high but not crazy

4 genuine brake pads are just under 200$ trade . I wouldnt ever use bendix or some other crap ones . if your rotors are to low to skim they can set you back 250$ for decent DBA ones.

you should always do your water pump while your there changing the timing belt

Why don't you state the workshop you went to so that fellow SAU members will not go again :rofl:.

My major service cost me $1,000.

OEM Nissan Timing belt, OEM Nissan water pump, new battery, new O2 sensor, all bearings changed, coolant flush. Took slightly more than half a day to do.

I will prolly be sourcing my 100 000km parts from Kudos Motorsports (Sponser on here) as they have different kits for what you want to replace. I would recommand sourcing your parts from a sponser and then getting your mechanic of choice to install. I think each state needs a recommanded workshop sticky in each of their forums covering body, mechanical, suspension etc...

mine cost 3.6K.... although I pretty much replaced everything except the major Engine parts (half of the manifold and turbo studs were broken, requiring drilling, which took a lot of time, increasing labour costs)

got mine done at UAS. costly, but my car hasn't missed a beat (except for coils and a flat battery here and there)

i know its an import and that shit costs extra but i just wasnt expecting such a high cost, and from what most of you have said i have been taken for a ride. oh well these things happen,

about the brakes, i dont need the best brake pads in the world, afterall it is only an auto non turbo and i dont drive it very hard anyway (1 point left)

il get them done some time in the near future.

the reason why it took so long is because he had it over the weekend from late friday arvo(the only time i dont work) he also gave me a car to use on monday and today so i could get to work.

CAN ANYONE RECOMMEND A PLACE IN MELBOURNE THAT I SHOULD GO TO? i dont care what side of melbourne it is on.

my 100,000km kit cost me about $270 then i just put it all on myself :mellow: would be happy to do other people's for a small cost :rant:

cheers

CJ

ps, i did water pump and all that comes with the service kit from andrew (Kudos Motorsports)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...