Jump to content
SAU Community

Recommended Posts

Stopped at an intersection near my place in Springfield and a car almost identical to mine comes around the corner past me. I had the window down ready and said, quite loudly, "nice car mate!!"

He looked at me like I was from another planet... Very sad...

WAVE AT OTHER SKYLINES!!!!!!!!!

Stopped at an intersection near my place in Springfield and a car almost identical to mine comes around the corner past me. I had the window down ready and said, quite loudly, "nice car mate!!"

He looked at me like I was from another planet... Very sad...

WAVE AT OTHER SKYLINES!!!!!!!!!

Bogan :)

Spotted BECKS yesterday arvo merging onto Centenary Hwy Roundabout. I was in the Cefiro

Spotted B3CKS at M1 this morning. I was the black R34 sedan @ T2 Lane :(

Hey!! :)

I wondered if you were on here!

Wish i could cruise in the t2 lane in the mornings!!

Traffic's been crap latley!

See you out and about soon!

As some of you may know I wrote off my beautiful 33 S2 in June. However even now driving an Evo, Skylines still catch my eye. I spotted this hot metallic orange 33 at the Gabba and a gunmetal grey 4 dr 34 on Middle Rd, OUR 34........ :spank:

post-26685-1228527117_thumb.jpg

spotted yesterday white 34 4 door with black rims parked in Kuraby directly accross the street from my place. plates were blacks or something like that. nice car but if your on here i reccomend not parkin on that crest of the hill that guard rail was put there cos dickheads hoon up this street regularly and lose it. would hate to be havin a ciggy on my veranda and have to see a line get crumpled

spotted a white 34 in springwood saturday night with black bonnet no spoiler. looked sweet...

spotted a white 4 door pillerless 31 in coomera today. cant quite remember plates.. pretty sure had gtr in it.... very sweet.

:D:bunny::):bunny::banana:

Spotted Becks in the carpark in the valley yesterday. parked right near you so you could spot me haha

green r33

cars finally back on the road so should see me in there a bit more. you always arrive earlier and leave earlier than me though. im usually up on the higher levels

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...