Jump to content
SAU Community

Recommended Posts

yea HI i am the white 34 owner. YEA that was a bs race he smoked me. nice car btw i as looking right at you when i hcanged into 4th. i may have been speeding :P

Haha. I watched the whole thing while pulling out. You passed by, staring out while smoking haha.

I think i've seen yours around before, there are a lot on that road. for some reason, especially wingless 34's.

Haha. I watched the whole thing while pulling out. You passed by, staring out while smoking haha.

I think i've seen yours around before, there are a lot on that road. for some reason, especially wingless 34's.

hhaah i work in capalaba. its probly jsut me you see all the time lol

spotted a silver 33 out near Camira/Springfield around 630-645 this morning plates were &*033 not sure of letters i got a wave. if your on here i did wave back just bit of a slow reaction for me this morning still getting used to early wakeups.

8oosta- Blue 32 GTR nice nice very tidy heading south on gimpie rd near chermy, had a gd chat

gun metal grey 33 gts-t ??? driving south on i dunno which road lol i gave u the thumbs up anyway tidy car

was in my white 32 GTR with the Work rims

spotted a few skylines going to the hospital

a white 32 gtr.. looked kinda dirty and was pissing out blue smoke from the exhaust :) poor girl! @ goodna on the highway

a yellow 34 and a blue 34 @ the highway near oxley traveling together

another yellow 34 @ annerly

and a 4 door silver 34 @ redbank plaza lights plates were RWD-34 (i think)

spotted tons of skylines today a black 3 door R33 near the spit roundabout cheers for the wave !

also spotted a black R32 on wellington road near wello point cheers for a thumbs up :)

a few other R33s mostly white S1

Well that would have been me... I have made it my life's work to get Skyline owners to wave!!!

Was on my way to work... back there again tomorrow... Letters were DBR + the 33 bit...

yeah i usually down that road same time mate. i am working at that Pollaris data centre being built in springfield over near the orion? shopping centre. finish up this friday though i think.

Spotted a white 33 with sau stickers (165ijo) on the bruce highway this arvo (around 5.15pm). You took the d-day turn off.

I didn't wave cuz I couldn't get your eye contact and didn't wannna look like a dick lol

Edited by BLiNKsTaR

sorry guys my bad .. it was a 2 door ..

Just had a R32 roll 3 times over on mt gravatt capalaba road this morning i didnt get the plates was white had gtr kit and white wheels on it... hope the driver walked away ok...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Update: tested my spark plugs that are supposed to be 5ohms with a 10% deviation and one gave me a 0 ohms reading and the rest were 3.9ohm<, so one bad and the others on their way out.
    • 9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
    • I have an elite 2500 running an adapter harness on an rb25de neo r34. I took the butterfly out and removed all that junk. But I also went Plus+t at the same time. The butterfly thing works in reverse to the boost solenoid on the Gtt if that makes sense
×
×
  • Create New...