Jump to content
SAU Community

Recommended Posts

Bayside blue 34 GT-T Ser 2 I presume with the rear bar at capalaba.

Didn't notice you were a "skyline" driver until you got to your car. Did pick up that you had a bit more interest in the car than the average passer.

Hi :thumbsup:

Bayside blue 34 GT-T Ser 2 I presume with the rear bar at capalaba.

Didn't notice you were a "skyline" driver until you got to your car. Did pick up that you had a bit more interest in the car than the average passer.

Hi :)

pretty sure I saw you at the crossing of miles platting road and logan road today

pretty sure I saw you at the crossing of miles platting road and logan road today

Yeah, would have been me.

Was heading to Sunnybank for YumCha :)

Where were you?

On that note, mains road, R33, SAU sticker on front. At the intersection of plaza and markets, I waved.

Pink R32 on Old Cleveland Rd East - 2 girls in it, waved.

Silver R33 on same road, a bit ahead of them, waved.

Maroon R33 - prestige plates - on Allenby Rd, waved.

Oh and 70RTY on Sunday - Grieve Rd/Rochedale Rd R35 GTR :)

Hi :D

Edited by Owgasm
Seen a maroon R32 on Webster Rd yesterday or day before in the morning, got all excited thinking it was Isola, however i got closer and it wasnt.. I was prepped and wave ready and all for ya =]

haha what a let down

There's a blacky bluey greeny weirdish colored 33 in trouts rd at the moment... at the house where the white Honda lives. It's like someone took blackboard paint, and painted their 33... very odd.

Anyone from here?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • If you take the top half of the intake off you can unbolt the flap off the shaft and leave the shaft in there blocking the hole. Then you can remove the little vacuum canister off from under the manifold and get a spare vacuum line to run to the ECU. I can take some photos of it later. Probably best to get the vacuum source to the ECU sorted first though. Mine all worked mint with the base map from the GTT an I've pretty much let the closed loop sort the fueling and took 1 degree out of the whole timing map.
    • This IS something you also have to configure in Haltech (or at least I did in the past when going from onboard-to-ECU map sensor and an external MAP sensor in haltech land).
    • I'm hoping it's something as simple as the ECU is looking for an external MAP sensor, but he is trying to use the onboard MAP sensor.
    • You won't need to do that if your happy to learn to tune it yourself. You 100% do not need to do that. It is not part of the learning process. It's not like driving on track and 'finding the limit by stepping over the limit'. You should not ever accidently blow up an engine and you should have setup the ECU's engine protection to save you from yourself while you are learning anyway. Plenty of us have tuned their own cars, myself included. We still come here for advice/guidance/new ideas etc.  What have you been doing so far to learn how to tune?
    • Put the ECU's MAP line in your mouth. Blow as hard as you can. You should be able to see about 10 kPa, maybe 15 kPa positive pressure. Suck on it. You should be able to generate a decent vacuum to about the same level also. Note that this is only ~2 psi either way. If the MAP is reading -5 psi all the time, ignition on, engine running or not, driving around or not, then it is severely f**ked. Also, you SHOULD NOT BE DRIVING IT WITHOUT A LOAD REFERENCE. You will break the engine. Badly.
×
×
  • Create New...