Jump to content
SAU Community

Pod Filters Legal?

Alex_r33s2gts25t
 Share

Recommended Posts

R TUNE Mentor

R TUNE

Posted
Posted

they will be legal to my knowlage so long as you have the following contected,

pcv hose, o2 sensor, afm (basicly dont touch any hoses that are on the intake pip and you should be fine.

i got done buy a gop once for my pod told my boss the next day (was defected) and see it's legal casue all emission controlls were conected.

Sandeep Community Regular

Sandeep

Posted
Posted

i think (in vic) you're only allowed one intake mod (so you can choose one out of pod, larger front/side mounts, bigger throttle bodies, bigger turbos etc). but also it's an epa violation if the pod is an oiled filter (eg K&N) whereas a dry filter (A'Pexi etc) is legal as long as you comply with the 1 intake mod rule.

r33cruiser Grand Master

r33cruiser

Posted
Posted (edited)

it is confusing. i remember reading on boostcruising that the rda said u can only have 1 intake mod ie. a pod OR a fmic.

but if u had both, it is defectable?!?!!

and it has to be fastened in place, but they brought in a new one, that it has to be enclosed in a box

*this is scary when a cop was looking ova my engine bay, and i asked him if the pod was defectable (this was like 1yr to 6mths ago) it was a perception thing. in that different cops may think its defectable, when others are fine with it.!!!!

WTF???

Edited by r33cruiser
Eug Grand Master

Eug

Posted
Posted

check with your local authorities, it varies from state to state.

some states are only allowed one induction mod (i.e. filter OR intercooler)

some require the pod only to be braced

some require enclosed

do the research

some states don't even care, it's what the booking officer decides.

kcmagee Contributor

kcmagee

Posted
Posted

Hi Guys,

I work as a cop in NSW so I can give an insight on the legalities but only obviously for NSW.

Pod filters are illegal unless you have an enclosure. Further, blow offs can't vent into the atmosphere.. Basically if you have a engineer's certificate you are generally fine, but from my experiences most ppl never do especially with the tachos on the 'A' pillar. At the end of the day most cops will let it slide as long as you're not a smart arse when spoken to. And most general duties cops won't know what a pod filter is...

Hope this helps,

r33cruiser Grand Master

r33cruiser

Posted
Posted (edited)

http://www.transport.qld.gov.au/Home/Safet..._modifications/

this is qld. hope it helps.

*shit, my muffler is angled upwards, drift style, and thats illegal!!!! GAYNESS

Edited by r33cruiser
r33cruiser Grand Master

r33cruiser

Posted
Posted

u could go one of these, but still. i would actually call your state transport authority. or even better, just email your local police station. we can do that up here on the sunny coast, and they actually help.

http://cgi.ebay.com.au/Pod-Air-Filter-Fit-...1QQcmdZViewItem

R34GTFOUR Mentor

R34GTFOUR

Posted
Posted

In wa your allowed a pod filter as long as you have a bracket made up to secure it, it doesnt have to be inclosed and it can be oiled.

Just got a gtst across the pits, with a pod, fmic, exhaust and bov and they dont really care as long as its secured and wont fall off.

Like everyone said this will vary from state to state, and most of the time if your not a dickhead the cop will let you go, but the second your a smart ass they'll find something to defect you for even if its legal..

  • 3 months later...
EMZ R33 Community Regular

EMZ R33

Posted
Posted (edited)

Its best that your pod filter is boxed, for legal reasons and for proformance reasons.

Proformace wise, sucking in dirt, water and other crap prob isnt the best for any engine.

I have a clear case for R33 N/A's pods for sale, PM if interested.

PodCover3.jpg

PodCover1.jpg

Podcover2.jpg

regards, Evan

Edited by EMZ R33
R338OY Veteran

R338OY

Posted
Posted

There are many inconsistencies with this issue.

From my knowledge it must be enclosed to be legal. But it's still defectable if an officer decides it's defectable.

I doubt it's a problem in most cases when it's enclosed and you're just honest with cops, but if you're defected you have to change it to a stock airbox unless you have an engineer's certif. (which still isn't a guarantee).

I think in real-world circumstances you can manage fine with a pod, but it's always a grey-area.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...