Jump to content
SAU Community

R33 Boot - Water Leak

fleximoronx

By fleximoronx,
in Victoria

 Share

Recommended Posts

fleximoronx Rookie

fleximoronx

Posted
Posted

Hey guys,

The other day, my boot was flooded with 4 litres of rain water, due to the heavy rain recently.

This has never happened, so I'm assuming that the boot seal has been worn out.

Do you guys have any suggestions on the problem? Or if anyone has encountered something similar?

I wouldn't have a clue where to get new boot seal installed, if that was the problem...

Any help and assistance would be appreciated.

Thanks

Link to comment
https://www.sau.com.au/forums/topic/193110-r33-boot-water-leak/
Share on other sites
AutoTrust Mentor

AutoTrust

Posted
Posted

Take a small friend up to the car wash with a torch, cram them in the boot and spray away. Don't be afraid to pull the trims out to see what's going on.

Also look at the wiring running to the bootlid, the wiring grommet can fail and allow water to run freely into the right side of the boot area. Water leaks can suck to find.

Good luck.

fleximoronx Rookie

fleximoronx

Posted
  • Author
Posted
Also look at the wiring running to the bootlid, the wiring grommet can fail and allow water to run freely into the right side of the boot area.

I think this could be the case, given that water is only going through from the right side. How do you find out it's a wiring grommet failure? Are there tests I can do? (not even sure what a wiring grommet does... I'm a noob with cars, sorry.)

fleximoronx Rookie

fleximoronx

Posted
  • Author
Posted
it will be coming from the tail lamps....make no mistake

I had my car at the panel beater a while back, they fixed up the right hand tail light (someone scratched the rear and side panels)... maybe this could be the problem? If this could have caused the problem... maybe they didn't seal the tail light properly? but to have 4 litres of water coming through this small part of the vehicle is surprising... any suggestions? is that even possible?

Al Grand Master

Al

Posted
Posted
I had my car at the panel beater a while back, they fixed up the right hand tail light (someone scratched the rear and side panels)... maybe this could be the problem? If this could have caused the problem... maybe they didn't seal the tail light properly? but to have 4 litres of water coming through this small part of the vehicle is surprising... any suggestions? is that even possible?

YES :D

adznight Newbie

adznight

Posted
Posted
it will be coming from the tail lamps....make no mistake

Spot on, my old car the the exact same thing, pull them out, goop them and put them back in. You'll find it will happen when you park on a certain angle, well at least I did. You'll need a bit of muscle to pull them out though, that black silastic stuff can be tuff :yes:

DogKnight Mentor

DogKnight

Posted
Posted

On a slightly unrelated note my friend and I have been toying with the idea of putting a hole in the spare wheel bay and plugging it with a stopper so that when we go to a BBQ we can take out the spare tyre and turn the boot into an eski.

I was just thinking about water in the boot :wave:

Al Grand Master

Al

Posted
Posted
On a slightly unrelated note my friend and I have been toying with the idea of putting a hole in the spare wheel bay and plugging it with a stopper so that when we go to a BBQ we can take out the spare tyre and turn the boot into an eski.

I was just thinking about water in the boot :D

There should already be a hole under the spare wheel, that has a removable grommet. (R33)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R33 Fuel Pump & Brakes after alarm swap

      By GTSBoy · Posted

      Power is fed to the ECU when the ignition switch is switched to IGN, at terminal 58. That same wire also connects to the ECCS relay to provide both the coil power and the contact side. When the ECU sees power at 58 it switches 16 to earth, which pulls the ECCS relay on, which feeds main power into the ECU and also to a bunch of other things. None of this is directly involved in the fuel pump - it just has to happen first. The ECU will pull terminal 18 to earth when it wants the fuel pump to run. This allows the fuel pump relay to pull in, which switches power on into the rest of the fuel pump control equipment. The fuel pump control regulator is controlled from terminal 104 on the ECU and is switched high or low depending on whether the ECU thinks the pump needs to run high or low. (I don't know which way around that is, and it really doesn't matter right now). The fuel pump control reg is really just a resistor that controls how the power through the pump goes to earth. Either straight to earth, or via the resistor. This part doesn't matter much to us today. The power to the fuel pump relay comes from one of the switched wires from the IGN switch and fusebox that is not shown off to the left of this page. That power runs the fuel pump relay coil and a number of other engine peripherals. Those peripherals don't really matter. All that matters is that there should be power available at the relay when the key is in the right position. At least - I think it's switched. If it's not switched, then power will be there all the time. Either way, if you don't have power there when you need it (ie, key on) then it won't work. The input-output switching side of the relay gains its power from a line similar (but not the same as) the one that feeds the ECU. SO I presume that is switched. Again, if there is not power there when you need it, then you have to look upstream. And... the upshot of all that? There is no "ground" at the fuel pump relay. Where you say: and say that pin 1 Black/Pink is ground, that is not true. The ECU trigger is AF73, is black/pink, and is the "ground". When the ECU says it is. The Blue/White wire is the "constant" 12V to power the relay's coil. And when I say "constant", I mean it may well only be on when the key is on. As I said above. So, when the ECU says not to be running the pump (which is any time after about 3s of switching on, with no crank signal or engine speed yet), then you should see 12V at both 1 and 2. Because the 12V will be all the way up to the ECU terminal 18, waiting to be switched to ground. When the ECU switches the fuel pump on, then AF73 should go to ~0V, having been switched to ground and the voltage drop now occurring over the relay coil. 3 & 5 are easy. 5 is the other "constant" 12V, that may or may not be constant but will very much want to be there when the key is on. Same as above. 3 goes to the pump. There should never be 12V visible at 3 unless the relay is pulled in. As to where the immobiliser might have been spliced into all this.... It will either have to be on wire AF70 or AF71, whichever is most accessible near the alarm. Given that all those wires run from the engine bay fusebox or the ECU, via the driver's area to the rear of the car, it could really be either. AF70 will be the same colour from the appropriate fuse all the way to the pump. If it has been cut and is dangling, you should be able to see that  in that area somewhere. Same with AF71.   You really should be able to force the pump to run. Just jump 12V onto AF72 and it should go. That will prove that the pump itself is willing to go along with you when you sort out the upstream. You really should be able to force the fuel pump relay on. Just short AF73 to earth when the key is on. If the pump runs, then the relay is fine, and all the power up to both inputs on the relay is fine. If it doesn't run (and given that you checked the relay itself actually works) then one or both of AF70 and AF71 are not bringing power to the game.
    • Kinkstaah
      My BMW E39 528i touring

      By Kinkstaah · Posted

      @PranK can you elaborate further on the Colorlock Dye? The website has a lot of options. I'm sure you've done all the research. I have old genuine leather seats that I have bought various refurbing creams and such, but never a dye. Any info on how long it lasts? Does it wash out? Is it a hassle? What product do I actually need? Am I just buying this kit and following the steps the page advises or something else? https://www.colourlockaustralia.com.au/colourlock-leather-repair-kit-dye.html
    • GTSBoy
      My BMW E39 528i touring

      By GTSBoy · Posted

      These going to fit over the big brakes? I'd be reeeeeeeeaaaall hesitant to believe so.
    • PranK
      My BMW E39 528i touring

      By PranK · Posted

      The leather work properly stunned me. Again, I am thankful that the leather was in such good condition. I'm not sure what the indent is at the top of the passenger seat. Like somebody was sitting in it with a golf ball between their shoulders. The wheels are more grey than silver now and missing a lot of gloss.  Here's one with nice silver wheels.
    • soviet_merlin
      My BMW E39 528i touring

      By soviet_merlin · Posted

      It's amazing how well the works on the leather seats. Looks mint. Looking forward to see how you go with the wheels. They do suit the car! Gutter rash is easy to fix, but I'm curious about getting the colour done.
×
×
  • Create New...