Jump to content
SAU Community

Recommended Posts

you heard the nazi mod. VOTE 1 Me..

hanson..?? i did not have sexual relations with that woman!!!... maybe

ive never been done for speeding its always RBTs and smacks for having mods on my car.. in the GTR.. i got pulled over for speeding up the back of a cop and backing off. he couldnt prove my speed so he smacked my wrist.. i enjoyed it

lool, if i remember correctly. your "smooth"

as far as voting, i dont think its up to ruddy or howard where cameras go, that all goes on in the police departments, they are self funded, hence the dodgy placement and no warning on cameras, (revenue raising) u can vote for who u like, in the end, unless either party says no to speed cameras or promises to sign post them all etc... its gona happen...

and RBT's are still common, well ive had a few, but my money is on them testing imports etc more than others....

Edited by RusH_
  • Replies 95
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Our police mistress said on the TV news last night that the cameras would be set at 1kph over the limit.

Now all of my cars are of an age where the standards for speedo accuracy was 10%

So doing the maximums math, and not allowing any tolerance on their equipment, I have to do 92 to register 101 on their camera.

92kph on a brand new freeway (Burpengary) that should have been signed at 110 anyway!!!!!!

Then allow a little less for the nervous types and you've got a recipe for multiple nose/tail collisions.

This is nothing more than a money grab hiding under the guise of road safety.

So basiclly what your saying is, just cruise past the speed camera at much much less than the signed speed limit...

Ie. Hold up traffic...? Cause i dont care what others behind me think, Ill go as slow as i want to make sure i dont trigger the damn thing...

Its like when you see a camera on the highway and you only doing 100 anyway, you still break and cruise past it at like 95 just to be sure...

1 kmph tolerance what a crock of crap, thats pretty much zero tolerance and will cause more dramas more crashes ie nose to tail esp in peak times, and here is the law trying to prevent injuries and damages? go figure that one out i cant

did anyone drive over the story bridge this morning? i didn't see a single sign for them

apparently they all have like 5 signs clearing stating that they are there or some shit

i didn't even see where they were

typical, of course the dnt wana sign post it, then ppl who dont know about it will get caught...

i saw one of those 4wd's on the side of the road the other day, noticed cos sum1 comin the other way high beamed, nehow, they had a sign saying speed camera being used or sumtin, it was placed about 1m from the car...

how is someone supposed to see that and realise they could get caught...i guess they arent meant to

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Don't be ridiculous. "2-3 ugga duggas or one Oof. You have to use Oof on tie rods because you can't get an ugga dugga on there." Is not helping the guy at all.
    • I have done a lot of research before posting here and on gtruk forum. couldn't find anything. I have my gauges all part except the needle itself. the needle has a extremely small hole in the center, but the shaft going to the needle is extremely small and appears to have nothing to index it either. doesn't seem strong enough to simple pry or pull without damaging something. Already tried the old spoon trick on a extra triple meter I have from a gtt, but no luck. the center cap comes off easily but the hole in the meter face plate aren't big enough to get over the needle itself. figured this would be my best place to find someone who might have actually removed theirs. wonder if there is some type of small pin press tool to push the pin in while pulling the needle base off.
    • Ok...its taking me long enough to finally do this.  Feck financial security...heart disease will get me soon enough anyway So welcome to the garage..."Clem" Belsil80 has been running a 370Z in Super TT series. So after entering with him in last years Winton 300 i figured I  need my own car. Seems SAU Vic race cars need to be yellow....{tick} Reckon with enough motor i will be able to make up for the lack of talent and stay ahead of the 370Z... but the LS powered S13 and E36s are a ways up the road Aim is to have a car that doesnt stop or turn but has a bit of shed built motor with jam...maybe some cream  First step is getting this ex drift car log booked I am keeping faithful silver car. As the road-club car gets upgrades the race car wil get the sloppy seconds
    • Assuming that they will come off without damage at all.... i would have thought just pull straight up off the spindle with a something or other than can reach underneath. Have you searched for youtube vids of people doing similar on R34s or any other Nissan from the same vintage? They should be the same technique, in all likelihhood.
    • Keeping in mind that sandblasting is really aggressive on softer metals like cast alloy, and you can do damage that you might regret. For trash wheels, not a problem. For wheels with value/scarcity issues, etc.... perhaps a less aggressive media is a better choice?
×
×
  • Create New...