Jump to content
SAU Community

Recommended Posts

Gday All,

I am currently considering buying a set of coilovers (Tein SuperStreets) for my skyline but I am a bit unsure of a few things.

The main thing I am am concerned about is the legality of coilovers.

Obviously apart from the ability to lower you car below the legal limit, is there anything else which can cause them to be illegal?

Do the need to be of a certain shock design?

Do they need to be ADR approved?

I am in Queensland if it makes any difference...

Any help will be appreciated...

Cheers

ShanO`

Link to comment
https://www.sau.com.au/forums/topic/194555-coilover-legalities/
Share on other sites

as far as i know they are illegal for a few reason, i think one is ADR but the other is they dont have spots to hold the brake lines, in saying that there are plenty of cars that have them and dont get pulled up for it, so just make sure the car isn't too low and you should be ok

Let me rephrase that..............

Skylines have coil overs standard, the coil springs go OVER the shocks absorbers.

So coil overs are NOT and NEVER will be illegal.

Citroens have had in cabin height adjustment for over 40 years, so that can hardly be illegal.

Mercedes had and still do have height adjustment via aribags.

Plenty of late 70's Jap cars had in cabin adjustable shocks, so that can hardly be illegal.

What then is illegal? It is spelt out in the ADR's, too low (100 mm minimum) and less than 2/3rds of the original suspension travel.

Simplistically, if your R32/33/34 is lower than 355 mm at the front and 345 mm at the rear then it pretty much guaranteed to be illegal.

Back to the original answer, for less money you can buy a much better shock absorber than a Tein.

Cheers

Not sure about QLD but in NSW you need to have them engineered to have no worries, reason is say you get defected for ride hieght, all you do is go home and raise the car, clear it, then drop it again.

First thing a cop asked me when i raised my bonnet?"Your suspension engineered?"

(Apparently the engineer must measure the car at the lowest 100mm ground clearance, then destroy any residual thread on the coil over that would cause it to go lower).

there's nothing inherantly illegal about coilovers. most cars including skylines come with coilovers from the factory.

Gary....ouch.

Sorry, Matt was having a bad day, I have edited appropriately

Cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..    If i get this - will this fit all around: Size: 18 x 8.5 +37 - n what tyres size tyre should i get for front n back?  
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...