Jump to content
SAU Community

Recommended Posts

  • Replies 153
  • Created
  • Last Reply

Top Posters In This Topic

lots of people run nos on the street even though it is illegal, most say as long as its not hooked up your fine unless you attract their attention...

I've stayed away from it because of the defect factor... you should be able to get away with it, it would just worry me that one day if you get a defect it means you would have to pull it all out to get rid of the defect notice.... otherwise eveyone would do it...

A good mechanic should be able to do a virtually indetectable install, along with a custom stereo will provide and area to hide the bottle... Thats how mine was anyway...

Bit if its a show car.. its lost all of its bling..

THE RESULTS ARE IN!!!!!!!!!

Ok everyone.... im pretty happy with the final results, i could have gotten more, but decided against it as i preferred to stay in the "safe" zone to begin with.

128 kW at the rear wheels without nos

and 152 kW at the rear wheels with nos.

like i said before im happy with the results, as i have stay in the safe zone.

:D

Not sure about S.A.; but in VIC if a car is caught with any part of a NOS kit installed, a fine of $2000 per cylinder applies. That's right ;) $12,000 for our cars. If this is an EPA issue (not roadworthy) then i dare say the fine applies nation wide.

Not to burst your bubble, but is 24rwkw really worth the risk? Especially when a 100% standard GTT produces that power and probably a little more. Put an exhaust, fmic, Pfc and some more boost, on a GTT, and you wont be anywhere to be seen :D .

hmmm...i would be looking carefully at the graph with the NOS

there is only a 24kw increase in peak power (which is about 32 HP)

really there should be around a 55kw increase as NOS is fairly affective at achieving the stated HP gain...

i want to see a torque curve....

umm... nitrous is basically air just with a slightly higher oxygen saturation (33% compared to ~20%ish)

regardless its still air/N2O (oxygen) under pressure being forced into the intake - doubtful that it would account for 18kw, i think the difference is mainly the dyno.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Hi...a bit a "development" on the brakes. I spoke to the guys where i get brakes from...and they are saying that 296mm EBC are for R34 GT-T. I then went to their site: https://www.ebcbrakes.com/vehicle/uk-row/NISSAN/Skyline (R34)/ and search for my car(R34 GT 1998 - it has GTT brakes) and it show me this USR1229 number and they are rly 296mm rotors... So now iam rly confused... The rotors i have now on the car are 310mm asi shown... So where is the problem? Does the whole EBC got it wrong or my calipers are just...idk know what?  
    • Oh What the hell, I used to get a "are you sure you want to reply, this thread is XX months old" message. Maybe a software update remove that. My bad.
    • This is a recipe for disaster* Note: Disaster is relative. The thing that often gets lost in threads like this is what is considered acceptable poke and compromise between what one person considers 'good' looks and what someone else does. The quoted specs would sit absurdly outside the guards with the spacers mentioned and need  REALLY thin tyres and a LOT of camber AND rolling the guards to fit. Some people love this. Some people consider this a ruined car. One thing is for certain though, rolling the guards is pretty much mandatory for any 'good' fitment (of either variety). It is often the difference between any fitment remotely close to the guards. "Not to mention the rears were like a mm from hitting the coilovers." I have a question though - This spec is VERY close to what I was planning to buy relative to the inboard suspension - I have an offset measuring tool on the way to confirm it. When you say "like a mm" do you mean literally 1mm? Or 2mm? Cause that's enough clearance for me in the rear :p I actually found the more limiting factor ISNT the coilover but the actual suspension arms. Did you take a look at how close those were?
    • @GTSBoy yeah sorry i know thery are known for colors bud those DBA are too in colors 🙂 Green will be good enough for me  
    • That's my life. Past-Duncan has a lot to answer for
×
×
  • Create New...