Jump to content
SAU Community

Recommended Posts

Hey

My coolant overflow bottle is filling up and spitting coolant out of the "hole" on the very top of the bottle.

Last weekend when i gave the car a bit of full throttle action i noticed that the stock temp gauge was sitting just between the half way mark and the full mark, so pulled over but left the car running, couldnt see any coolant spilling from any pipes anywere, but the overflow tank was completly full (didnt overflow though) so i drove the car back home very slowly.

One thing i have noticed is that when the car is up to full temp the radiator pipes are never hard (pressurised) ,in my old car the top radiator pipe would always be hard as a rock, mine is soft and almost feels like its empty, so i thought maybe the radiator cap is stuffed, went out and bought a new cap which changed nothing, pipes still soft and coolant overflow bottle is filling up.

The coolant system is always full and i check the level all the time, there are no leaks anywere at all, the waterpump and thermostat are nissan items that were replaced about 6months ago.

Any ideas what the problem could be? im thinking possibly a blocked radiator?

Any suggestions would be awsome

Cheers

Link to comment
https://www.sau.com.au/forums/topic/196137-coolant-overflow-bottle-overflowing/
Share on other sites

At a guess I'd say your pressurizing the cooling system ! do you get any hydrolic lock on start up ???

What exactly do you mean by hydrolic lock on start up?

The car starts and drives perfectly.

By the way, i forgot to mention that after the stock water temp gauge went between medium and high i went home and plugged in my power fc (still on the stand base tune) and went for a very slow/quiet drive , the water temp sat on 95deg most of the time, which seems a bit high to me?

I have the same problem except mine just blew the radiator recently. Get under the car and check for leaking welsh plugs. I replaced the radiator cap and kept topping up the motor and flushing it until I realised it was a stuffed welsh plug which would suck air back into the motor which caused a massive pressure build up when I turned off the motor.

(I happened to accidently pop mine into the block so I wouldn't do what I did to repair it)

he has already changed the cap. what about a air lock? when you go out to the car of a morning (or anytime where the car has sat for 6-9hrs) is there anything on the ground?? leaked coolant? trace it back to where its comming from.

1. get your radiator flushed (specially with summer now)

2. check all welsh plugs and hoses for leakes

and hoses arnt spose to be rock hard, go to repco or somewhere and feel new hoses :whistling:

he has already changed the cap. what about a air lock? when you go out to the car of a morning (or anytime where the car has sat for 6-9hrs) is there anything on the ground?? leaked coolant? trace it back to where its comming from.

1. get your radiator flushed (specially with summer now)

2. check all welsh plugs and hoses for leakes

and hoses arnt spose to be rock hard, go to repco or somewhere and feel new hoses :whistling:

The car never leaks coolant ever, the only time it has leaked coolant was yesterday when the overflow oveflowed lol.

I will give the car a flush today and change the coolant

I meant the hoses are spose to be hard when the car is at full temp and the coolant system is pressurised, lol , but mine are always soft when the car is at full temp, probally because most of the coolant run into the oveflow tank and then overflow, hence not much pressure in the system because there is hardly any water actually in the motor.

I've had 2 cars that have done this, it was headgasket both times.

I hope not lol, but somehow i dont think so, as the car isnt blowing any white smoke, its not losing coolant apart from when it spews its out the overflow, the car still runs perfect.

thermostat may not be opening fully or siezed partially open

Thermostat is about 6months old and was a brand new nissan item which was replaced when i got the waterpump/cambelt etc etc done.

Looks like i may have found the problem!

Took out radiator and the top and bottom radiator hoses today, coolant was suprisingly nice and clean, but the top raditor pipe was full of rusted metal crap, the big nipple on the intakemanifold were the top raditor hose connects to has rusted away at the front of the nipple (see pic) which has obviously been rusting for a while sending rusted grunk crap threw the motor/radiator etc etc, which has probly blocked the radiator causing the car to overheat, the bottom of the overflow tank was full of brown rusty water which i didnt spot before hand.

Possibly one of the previous owners didnt use antifreeze, or not enough antifreeze which has caused the steel nipple on the intake mani to rust pretty quickly, hence causing my problems.

I will try and give the nipple a bit of a clean up and get most of the rust off, then flush the whole system heaps times, instead of get the stock radiator flushed/cleaned i might get an alloy one instead (will help with cooling when i start doing some track racing) ,and some new coolant ofcourse, i will update this thread when i have everyhing back together and hopefully fixed.

Pics of rusty nipple!

100_2024.jpg

100_2026.jpg

100_2027.jpg

Cheers for your help :)

  • 2 weeks later...

Turns out the radiator isnt the problem (i dont think).

Got the car running tonight (new alloy radiator and coolant) and had it idling while i was toping up the radiator wating for the thermostat to open, the car was idling for atleast 20mins, but the thermostat never opened, the water level of the radiator hardly dropped even when the car was up to full temp, the bottom radiator pipe stayed cold so im guessing the thermostat isnt opening.

That should have been the 1st thing i shouldve taken out and tested, i just ruled it out because its only about a year old genuine nissan item, not sure how it can all of a sudden go faulty, seems weird to me, the car was running fine and didnt overheat after nissan had replaced the thermo,waterpump/cambelt etc etc.

Anyway, what brand of thermostats do you guys use? im not really to keen on getting another nissan one if its just going to go faulty again (i bought the nissan thermo in the 1st place because if thought it would be the most reliable one, i guess not).

Cheers

you have a blown headgasket

Why do you say that?

The car does not blow white smoke, it does not use water, there is no oil in the water, there is no water in the oil and the car runs perfect! i dont have any of those issues.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The answer to this would be I followed the documentation from Turbosmart which said each spring pressure could achieve a maximum of 5x it's rated pressure so the included smallest spring being the 6psi had a range up to 30psi. I went with the 12 because I figured it'd likely hover around 15psi as a base pressure however I was obviously wrong.    I have a log here that I'll dig out that is purely wastegate and no Mac valve controlling anything.   If it can't hold anywhere near 12psi, does that mean the straight gate is virtually wide open during a run? Or am I thinking about this all wrong.   I could Tee Piece into the cooler pipe pre intercooler where the wastegate gets its feed, and send that to the ecu and see how that reads, I just don't have a spare pressure sensor currently that's all.
    • lol nice, I wouldn't worry about sanding back the filler to check for rust then. Yep very much a thing. Personally I don't do the panel beating, its very easy to have a panel beater sort that out for you. If they aren't doing any prep work the actual panel beating generally doesn't take long at all.  Have you taken before pictures before you started this project? I'd be keen to see the before and afters when you're done.
    • Some good discussion in here, for the most part I can't really add too much to it - thought I'd add some notes to the datalog screen shot that probably aren't news to anyone but a good prop... this is assuming 25psi-ish should be the boost ceiling given the first post refers to 23psi.   To state the obvious, this issue seems super weird.  Turbo speed seems pretty lethagic to build, like the turbo isn't getting as much drive as it needs - and it doesn't help that wgdc keeps rising AFTER boost target then completely shuts duty at a point, which in theory should have the straight gate dump heaps past the turbo and funnily enough causes the huge drop off.  It seems like pretty blunt boost control tuning but I'd not call that the primary issue, so much as possibly not helping the situation. I'm curious, what does a pull look like with purely mechanical boost control?  Like purely wastegate?   There are things in this log and story that make it sound like there could be a significant restriction in the intercooler piping or something - but then it's also overshooting boost target which is NOT what you'd expect with a restriction.   I can see where people are coming from with the non-linear wastegate bypass (not that any valves are linear for this kind of thing), but it still doesn't make sense that it can't hold <20psi on a 12psi spring.    Have you, or can you try measuring pressure pre-intercooler?  Be pretty interesting to see what's happening there vs in the intake manifold - sorry if I've repeated old ground, I've kinda skimmed over but I could have missed something.  In terms of comments regarding the wg spring being closer to boost target, I haven't used a straight gate but part of the reason for having close to wg target is about fighting backpressure as well - I might be wrong, but I'd have thought that part of the point of using a butterfly valve like the straight gate does you actually don't have to resist pressure at all, on EITHER side of the gate.   It shouldn't need too much leverage to start opening, the spring being more to do with where it triggers opening as opposed to resisting boost & EMAP, though smarter people can correct me if I'm wrong there.  
    • Ah the car is a complete shitbox and not even worth a respray lol, for a professional to do it would probably cost 15k because of all of the dings and stufd but I was keen for a side project. Also solved the problem of being bored haha. But with the rust yeah I can always fix that in the future, not a huge issue for me. I found out yesterday that when a dent is created a high spot is created around it (the crown) and to fix it I either need to tap the edges or just sand over it. Which is what made my filler work a bit confusing originally lol.
    • That's some useful information to have , it would be great if we had more local suppliers .
×
×
  • Create New...